manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 77 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 77

77 

Installation and Service Guide: Color Controller E-36A

Replacing Parts

Power supply

This section describes how to remove and replace the E-36A power supply. For more information about the power 

supply, see 

“Specifications”

 on page

 123.

To remove the power supply

1

Access and open the E-36A (see 

page

 50

).

2

Remove the 24-pin power cable from the motherboard (see 

page

 49

).

3

Remove the 4-pin power cable from the motherboard (see 

page

 49

).

4

Remove the power cable from the power connector on the HDD (see 

page

 49

).

5

Remove the power supply cables from the plastic clips that secure them to the chassis.

6

Remove the four screws that attach the power supply to the chassis (see 

page

 78

).

Set the screws aside so that you can replace them later. 

Do not open the power supply for service or troubleshooting. Opening the power supply will void 

the warranty.

Summary of Contents for E-36A


































































































































Reviews:

No comments