EFI E-36A Installation And Service Manual Download Page 101

Page: 101 / 129

101

Installation and Service Guide: Color Controller E-36A

Installing System Software

If you are replacing the HDD on the E-36A with a spare SATA HDD, you need a SATA to USB adapter to connect the

SATA HDD to a USB 3.0 port on the Windows computer having the Fiery Installer Builder.

Note:

SATA to USB adapter is shipped inside the optional Service Kit for E-36A.

To prepare the SATA HDD

Attach the SATA to USB adapter, to an USB 3.0 port on your computer.

Connect the replacement SATA HDD to the other end of the SATA to USB adapter.

Start the Fiery Installer Builder.

Double-click the Fiery Installer Builder icon on the desktop or you can also click

Start

EFI

Fiery Installer Builder

At the

Downloaded

window, select

Color Controller E-36A 1.0

From the

Prepare action

pull-down menu, select

Prepare SATA HDD, and

click

Next.

At the

Select a SATA HDD

window, click the replacement SATA HDD that you connected, and click

A warning message “This HDD will be formatted and all the data in this HDD will be lost.” appears. Click

format the HDD and proceed.

The SATA HDD will be formatted and the E-36A system software will be copied to a recovery folder on the SATA

HDD.

Once the SATA HDD is prepared, remove the SATA HDD from the SATA to USB adapter.

You can use this SATA HDD as an replacement for the SATA HDD on the E-36A.

Install the system software using the prepared replacement SATA HDD

The E-36A system software is stored in a recovery folder on the prepared replacement SATA HDD. Replace the HDD

on the E-36A with the prepared SATA HDD and restore the E-36A system software from the recovery folder on the

SATA HDD.

To install the system software

Remove all the USB devices that are attached to the E-36A.

Shut down the E-36A (see

page

Remove all external cables from the E-36A.

Replace the SATA HDD on the E-36A with the prepared replacement SATA HDD (see

page

Plug the power cable into the wall power outlet.

Improper handling can damage the HDD. Handle the HDD with extreme care. See

All the data on the HDD will be lost when you format the HDD. Make sure that no valuable data

is stored on the device.

Summary of Contents for E-36A


































































































































Search results

Summary of Contents for E-36A

Reviews:

EFI E-36A, Installation And Service Manual, Page: 101 / 129

Search results

Summary of Contents for E-36A

Reviews: