manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 89 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 89

89 

Installation and Service Guide: Color Controller E-36A

Performing Backup and Restore

•

Server Presets

•

Fonts

•

Job Log

Note:

 

Those settings you do not choose are not saved for restore. 

If you cannot create a configuration file, ask the site administrator to archive custom color profiles, preflight presets, 

FreeForm masters, customer-installed fonts, and the Job Log to removable media or a network location.

To save the system configuration from Command WorkStation

1

Launch Command WorkStation and connect to the E-36A with Administrator privilege. 

2

From the

 Server 

menu, click 

Backup and Restore

.

3

In the 

Backup & Restore

 dialog box, select 

Backup 

> 

Next, 

select the items you want back up, and then click

 Next

.

4

Enter a file name and location, specify if you want to add the date to the file name, and then click 

Next

.

5

Click 

Finish

. 

To save the system configuration from WebTools

1

Access Configure (see 

page

 32

).

2

On the left side, choose 

Fiery Server

 > 

Backup

.

3

In 

Backup

, select the items you want to back up.

4

Enter a file name and location, specify if you want to add the date to the file name, and then click 

Backup

.

5

Click 

OK

.

Restoring the system configuration

You can restore the system configuration of the E-36A to its previous state using a previously-saved system 
configuration file. For more information about the system configuration file, see 

page

 30

.

If you could not save a system configuration file, you must configure the E-36A settings. After you configure the 
settings, the E-36A reboots. Ask the site administrator to restore any archived settings and files. For more information, 
see 

Configuration and Setup

, which is part of the user documentation set.

To restore the system configuration from Command WorkStation

1

Launch Command WorkStation and connect to the E-36A with Administrator privilege. 

Note:

 

The default password (Fiery.1) will be set after any of the following:

•

You re-install the system software

•

You restore the recovery partition (from Fiery System Restore)

2

From the 

Server 

menu, click 

Backup and Restore

.

Summary of Contents for E-36A


































































































































Reviews:

No comments