manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 28 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 28

28 

Installation and Service Guide: Color Controller E-36A

Installing Hardware

10

Ask the site administrator to perform Setup and print some test documents over the

 network.

11

Store the output and the current Configuration page(s) near the printer.

12

After the site administrator completes the Setup, use the Fiery System Restore to copy the contents of the E-36A 

hard disk drive (HDD) to an image file. For detailed instructions, see 

“Using Fiery System Restore”

 on page

 90

.

13

Inform the site administrator that the E-36A user software must be installed on networked computers that print to 

the E-36A.

14

Ask the administrator to change the default password to avoid any unauthorized access to the admin account.

Configuring a static IP address for the E-36A

If the customer requires the E-36A to be configured with a static IP address (for example, in a non-DHCP network 

environment), obtain a valid static IP address from the site administrator and configure the E-36A.

To configure a static IP address for the E-36A from Fiery QuickTouch

1

On the Fiery QuickTouch display screen, press the 

Quick launch

 icon (see 

Figure 13

 on page

 34).

2

Select 

Settings

, and log in to the server as 

Admin

 using the default password.

3

Select 

Configure IP Address

, and select IP

 Address

, 

DNS

, 

Subnet Mask

, 

WINS

, and 

Default Gateway

, as necessary. 

4

Save the settings and exit. 

To configure a static IP address for the E-36A from printer operation panel

1

Press 

Home

 button on the printer operational panel.

2

From the 

Home

 screen, select the Fiery icon.

If the 

Fiery

 icon does not display, press the button on the upper right corner of the screen to switch to the icon view. 

3

Press the 

Fiery

 tab.

4

Press 

Setup

.

5

On the 

Login

 screen, press 

Password

. Enter the default password and press 

OK

.

6

On the 

Setup

 screen, do the following:

•

Press 

WINS

. If enabled (yellow), press 

Use WINS

 to disable this feature. Press 

Save

.

•

Press 

DNS

. If enabled (yellow), press 

Get DNS

 address automatically to disable this feature. Press 

Save

.

•

Press 

IP Address

. Enter an IP address. Press 

Save

.

•

Press 

IPv4 Address

. Press 

Manual Configuration

.

Summary of Contents for E-36A


































































































































Reviews:

No comments