manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 79 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 79

79 

Installation and Service Guide: Color Controller E-36A

Replacing Parts

5

Connect the 4-pin (2x2) power cable to the 4-pin connector on the motherboard.

For the location of the motherboard connector, see 

page

 49

. Connect the power cable to pins 1 through 4 of the 

motherboard connector. The cable is keyed to fit only one way.

6

Connect the 24-pin power cable to the 24-pin connector on the motherboard.

For the location of the motherboard connector, see 

page

 49

. The cable is keyed to fit only one way.

7

Make sure that all power connectors are properly aligned and securely connected.

8

Secure the power cables to the chassis using the two plastic clips on the base of the chassis.

9

Replace any tie-wraps that you may have removed or cut while removing the power cables earlier.

10

Reassemble the E-36A and verify its functionality (see 

page

 83

).

Hard disk drive (HDD)

The factory-installed HDD is formatted and loaded with system software, network drivers, and printer fonts. The 

HDD is also used to store spooled print jobs. Available space on the hard disk drive is displayed in 

Command

 WorkStation.

If you replace the hard disk drive with a new one, you must restore the backup (see 

page

 92

) or install system software 

as described on 

page

 96

. (Spare hard disk drives are not shipped with preinstalled system software.) 

It is unlikely that both the hard disk drive and the motherboard are defective. Avoid replacing both to solve one 

problem. If troubleshooting strategies (such as checking cables and connections; see 

page

 108

) do not solve the 

problem, and you suspect either the hard disk drive or the motherboard is at fault, use the following order to 

troubleshoot: replace the hard disk drive, install system software, and then check to see if the problem persists. If

 it 

does, perform other procedures, such as replacing the motherboard (see 

page

 63

). 

Proper handling

•

Use standard ESD 

“Precautions”

 on page

 

12 when grounding yourself and the E-36A.

•

Keep magnets and magnetic-sensitive objects away from the HDD. 

•

Do not remove the screws on top of the HDD. Loosening these screws voids the

 warranty. 

•

Never drop, jar, bump, or put excessive pressure on the HDD.

•

Handle the HDD by the sides and avoid touching the printed circuit boards.

•

Allow the HDD to reach room temperature before installation.

HDD problems may be caused by the following:

Do not replace the hard disk drive and the motherboard at the same time. Doing so in the wrong 

order, without updating the system (see 

page

 105

), will cause the system to malfunction. 

Improper handling can damage the HDD. Handle the HDD with extreme care:

Summary of Contents for E-36A


































































































































Reviews:

No comments