EFI E-36A Installation And Service Manual Download

Page: 105 / 129

105

Installation and Service Guide: Color Controller E-36A

Installing System Software

Back up the E-36A hard disk drives.

System software installation error messages

If an error message displays when you install or upgrade system software, do the following:

•

If prompted, save the log.

•

If you are not prompted to save the log, record the error message.

•

If the network cable and printer interface cables are still connected to the E-36A, disconnect the cables and

perform the installation again, starting from

“Installing the system software”

on page

96.

If you cannot correct the error, contact your authorized service/support center. A log or error message may help to

solve the problem. Provide as much specific information as possible.

Installing system updates

It is recommended to schedule the system updates from WebTools to automatically download and install the patches.

If the customer does not permit to schedule the system updates, install the patches from Command WorkStation. If

Internet connection is not available at the customer site, manually download the patches from

web updater site

and

install them according to the order listed on web updater site.

As part of reinstalling or upgrading system software, you must reinstall the system software patches. For a list of

patches that were installed on the E-36A, see the Server Configuration page that you printed before reinstalling the

system software.

To install the patches from WebTools

Access Configure (see

page

Click the

Fiery Server

tab

> System Updates > Enable System Updates

and

schedule the system updates to

automatically check for updates.

Choose between the available download options and configure the proxy settings.

To install the patches from Command WorkStation

Launch Command WorkStation and login to the E-36A with Administrator privileges.

The default user name is Administrator or Admin, and password is the administrator password set by the site

administrator.

From the

Server

menu, select

Device

Center

Device

Center

, click

FIERY UPDATES > Patches

on the left side.

Note:

If System Updates is scheduled to automatically check for updates, Fiery Updates displays a message for

disabling the scheduled automatic updates in System Updates. To disable the scheduled automatic updates in

System Updates and to enable the Fiery Updates in Command WorkStation, click

Continue.

Summary of Contents for E-36A


































































































































Search results

Summary of Contents for E-36A

Reviews:

Related manuals for E-36A

Brands by name

Popular brands

EFI E-36A, Installation And Service Manual

Search results

Summary of Contents for E-36A

Reviews:

Related manuals for E-36A

Brands by name

Popular brands