EFI E-36A Installation And Service Manual Download

Page: 96 / 129

Installation and Service Guide: Color Controller E-36A

Installing System Software

•

User software:

The

E-36A ships with preinstalled user software on the hard disk drives. During system software

reinstallation, you are prompted to reinstall user software (including Command WorkStation) from WebTools. For

more information, see

Utilities

, which is part of the user documentation set.

•

System updates log:

When you reinstall system software, the applied system updates are deleted. Print the Server

Configuration page (see

page

) to see the list of applied system updates. The applied system updates are listed

under the Fiery Updates, Application Updates, and OS Updates sections of the Configuration page. If there have

been no patches added to the system software, the System Updates sections will not be listed in the Configuration

page nor will the System Updates be listed in the Fiery Ticker.

•

Compatibility:

If you upgrade system software, remind the site administrator to upgrade the user software on all

computers connected to the E-36A. Using the old user software with the new system software may negatively affect

the system.

Before you install or upgrade system and user software

Before you proceed, do the following:

•

Ask the site administrator to:

•

Save the jobs to a removable media or a network location.

•

Print the Job Log, Server Configuration page, and Font List (see

page

•

If any options are activated on the server, you must deactivate them prior to reinstalling.

•

Archive and export any customer-installed fonts and FreeForm masters to an external hard drive, USB

storage device or network folder.

•

Save and export to an external hard drive USB storage device or network folder any custom simulation

profiles and custom spot color settings, if possible.

•

Disable the power synchronization (see

page

If you are installing system software, back up the system configuration.

For more information, see

page

Installing the system software

To install the system software, you need the following items:

•

Fiery Installer Builder

Using Fiery Installer Builder you can download the system software files from EFI cloud server and prepare a USB

flash drive or SATA hard disk drive (HDD) to install the system software.

Remove all dongles and devices on the E-36A. If you do not remove dongles or devices, the

system software installation may fail.

Summary of Contents for E-36A


































































































































Search results

Summary of Contents for E-36A

Reviews:

Related manuals for E-36A

Brands by name

Popular brands

EFI E-36A, Installation And Service Manual

Search results

Summary of Contents for E-36A

Reviews:

Related manuals for E-36A

Brands by name

Popular brands