manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 40 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 40

40 

Installation and Service Guide: Color Controller E-36A

Using the E-36A

Printable Info menu

This section describes how to print pages such as the Test Page and Configuration page from the Printable Info menu 

(described on 

page

 30

). The Printable Info menu is accessed through the Fiery tab (see 

page

 39

).

Printing the 

Configuration page

 can be helpful during installation, Setup, and service. After installing the E-36A 

(including connecting to the network), and before default settings are changed in Run Setup, you can obtain a record 

of the defaults by printing the Configuration page. 

Before you perform any service procedure, you should print the E-36A Configuration page, if possible, so you are 

prepared to return the settings to their former configuration, if necessary. 

Printing the 

Test Page

 indicates that the E-36A is functional and that the connection between the E-36A and the 

printer is working. 

To print a page from the Printable Info menu

1

If it is not powered on already, power on the printer and allow it to warm up. 

2

If it is not powered on already, power on the E-36A using the power button on the front panel and allow it to start 

up completely (approximately three minutes).

3

Make sure that Idle appears on the Fiery Main menu.

If Busy or Printing appears, the E-36A is processing and you must wait until Idle appears.

4

Touch the Fiery tab.

5

Touch Printable Info and then select the page that you want to print.

The E-36A sends the selected page(s) to the printer.

Clear Server

Clear all jobs in all server queues, as well as all jobs archived on the E-36A hard disk, 

the index of archived jobs (in the Archive window), all FreeForm masters, and the index 

of FreeForm masters (in the FreeForm window). Consult with your administrator or 

operator before choosing Clear

 Server. 

Restart Fiery

Shut down all E-36A activity in the correct manner and then restart. The following 

options are available from the submenu that appears:

Restart Fiery Service: 

Resets the server software but does not reboot the entire 

system. Network access to the E-36A is temporarily interrupted and all currently 

processing jobs are aborted and may be lost.

Restart System: 

Shuts down and then reboots the E-36A. Network access to the E-36A 

is terminated and all currently processing jobs are aborted and may be lost.

Shut Down: 

Shuts down all E-36A activity properly.

Summary of Contents for E-36A


































































































































Reviews:

No comments