manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 14 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 14

14 

Installation and Service Guide: Color Controller E-36A

Introduction

The power cable

Observe the following guidelines:

•

Only use the power cable that shipped with the E-36A or an appropriate replacement power cable. For replacement 

parts, see your authorized service support center.

•

Before you open the E-36A, unplug the E-36A.

•

Keep the power cable away from foot traffic.

•

Do not place objects on the power cable.

•

Do not plug the E-36A into a 2-hole, ungrounded outlet by means of a 3-prong adapter.

•

Do not plug the E-36A into a circuit connected to heating or refrigeration equipment (including a water dispenser).

•

Do not plug the E-36A into a switchable outlet.

•

Do not pull the cable to unplug the E-36A. Instead, pull the plug.

•

Do not tamper with or disable the power cable grounding plug.

•

Do not use an extension cord.

Summary of Contents for E-36A


































































































































Reviews:

No comments