manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 53 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 53

53 

Installation and Service Guide: Color Controller E-36A

Replacing Parts

Figure 30:

Removing/replacing the front panel

2

To replace the front panel, align the four tabs on the front panel to the tab holes at the front side of the chassis.

3

Press the front panel against the chassis and snap it into place.

Snap the tabs into place one at a time until all four tabs have engaged the chassis.

Fiery QuickTouch display module

Fiery QuickTouch is attached to the top side of the chassis.

You will need to remove the chassis cover and the front panel before you will be able to remove the Fiery QuickTouch.

1

Front panel

2

Tab (1 of 4)

 It is highly recommended that you use a screwdriver with a magnetic tip when removing or 

replacing the screws used to attach the Fiery QuickTouch. If you do not, the screws you remove or 

replace might fall inside the E-36A.

1

2

Summary of Contents for E-36A


































































































































Reviews:

No comments