manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 82 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 82

82 

Installation and Service Guide: Color Controller E-36A

Replacing Parts

Figure 44:

Removing the HDD bracket

8

Place the HDD in an antistatic bag.

Replacement HDD is shipped without any pre-installed system software. After installing a HDD, you must install the 

appropriate system software.

To replace the HDD

1

If you are installing a new HDD, unpack the drive. If you are not installing a new HDD, skip to 

step

  4

.

Do not drop, shake, or bump the HDD. Do not touch the HDD with magnetic objects or place magnetic-sensitive 

items near the HDD.

2

Place the HDD inside the HDD bracket, and align the two holes on either side of the HDD with the holes in the 

bracket.

Position the HDD inside the HDD bracket as shown in 

Figure 44

. 

3

Replace the four screws that attach the bracket to the HDD. 

Make sure that you use the same screws that you removed earlier. 

4

Position the HDD assembly inside the chassis, as shown in 

Figure 43

 on page

 81.

Position the lower edge of the HDD bracket over the mounting posts in the chassis, and press down firmly to 

engage the posts. 

5

Using the two screws that you removed earlier, secure the HDD assembly to the chassis.

6

Connect the SATA data cable to the SATA data connector on the HDD. Make sure that the other end of the cable is 

connected to SATA0 on the motherboard.

7

Connect the SATA power cable connector to the SATA power connector on the HDD.

The cable connector is keyed to fit only one way. 

1

HDD 

2

HDD bracket

3

Screws, HDD bracket (x4)

1

2

3

Summary of Contents for E-36A


































































































































Reviews:

No comments