manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 109 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 109

109 

Installation and Service Guide: Color Controller E-36A

Troubleshooting

Inspecting the system

If the system you are servicing does not meet a condition, and it is not obvious what action(s) you should take to fix the 

problem (for example, if the system hangs before reaching Idle), locate the symptom in 

“Table

 5:

 E-36A 

error 

messages 

and conditions”

 on page

 

113 and perform the suggested action(s) for the condition.

If your initial checks of the cable and board connections do not fix the problem, you may need to 

inspect the system on a component-by-component basis, as described in 

“Table

 : 

Inspecting 

the 

system”

 on page

 

109. A comprehensive inspection allows you to verify that each hardware 

component is properly installed and configured, and helps you avoid replacing expensive 

components unnecessarily. 

Summary of Contents for E-36A


































































































































Reviews:

No comments