manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 78 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 78

78 

Installation and Service Guide: Color Controller E-36A

Replacing Parts

7

Lift the power supply out of the chassis, taking care to gather the power supply cables.

Figure 42:

Removing the power supply

To replace the power supply

1

If you are replacing the power switch, locate the new power switch included with the replacement power supply 

kit. Orient the power switch as shown in 

Figure 42

.

2

Place the power supply inside the chassis (see 

Figure 42

).

Make sure to fit the power connector through the cutout in the chassis. Align the mounting holes in the power 

supply with the holes in the chassis.

3

Using the four screws that you removed earlier, secure the power supply to the chassis.

4

Connect the HDD power cable to the SATA power connector on the HDD.

1

Power supply cables

3

Power switch

2

Power supply unit

4

Screws (x4)

1

2

3

4

5

Summary of Contents for E-36A


































































































































Reviews:

No comments