manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 57 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 57

57 

Installation and Service Guide: Color Controller E-36A

Replacing Parts

For information about replacing other components, see the documentation that accompanies your printer.

Note:

 

There may be tie-wraps used to secure the cables to the chassis. If necessary, cut these tie-wraps before 

removing the components.

Printer interface board

The printer interface board provides the print interface between the E-36A and the printer. The printer interface 

board processes the image data and sends it to the printer through the printer interface cable available on the E-36A 

connector panel. It is installed in PCIE x16 slot on the motherboard.

Figure 33:

Printer interface board

To remove the printer interface board

1

Shut down the E-36A, remove all cables from the connector panel, and open the E-36A (see 

page

 50

).

2

Remove the cover (see 

Figure 25

).

Remove the screw that secures the cover mounted at rear side of the chassis. Set aside the screw so that you can 

replace it later.

3

Remove all the internal cables attached to the board.

4

Remove the screws that secures the board’s mounting bracket to the chassis.

Set aside the mounting screw so that you can replace it later.

5

Remove the board from the chassis.

Grasp the printer interface board at the front and back edges and gently pull the board straight out of the PCIE x16 

slot on the motherboard and place it in an antistatic bag.

Be sure to use an ESD grounding wrist strap and follow standard ESD (electrostatic discharge) 

precautions while performing these procedures. For details, see 

“Precautions”

 on page

 12.

1

OFF/ON switch connector for power synchronization

4

J102 connector for LED/SW cables from the Fiery QuickTouch panel

2

Type B USB port connector for power synchronization

5

J103 connector for 10-pin power button cable to motherboard J11 
connector

3

PCIE x16 connector

1

2

3

4

5

Summary of Contents for E-36A


































































































































Reviews:

No comments