manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 62 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 62

62 

Installation and Service Guide: Color Controller E-36A

Replacing Parts

2

Lift the motherboard edge opposite to the connector panel to release the motherboard from the chassis, and then 

gently lift the motherboard out of the chassis.

Note:

 

Make sure to lift the motherboard edge near the DIMM area, so that the underside of this area clears the 

nearby screw standoff.

Make sure that the connectors on the motherboard clear the cutouts in the chassis as you remove the board. Avoid 

handling contacts or using excessive force.

3

If you are replacing the motherboard with a new motherboard, remove the following from the old motherboard:

•

DIMM (see 

page

 67

)

•

CPU (see 

page

 70

)

Replacing the motherboard

Use the following procedure to replace the motherboard in the E-36A chassis. Failure to follow the instructions in this 

section may corrupt the system (not easily repaired in the field) or result in an incomplete installation.

Troubleshooting cautions

•

Before deciding to install a new motherboard, refer 

“Troubleshooting”

 on page

 107

.

•

Inspect all cables and internal components as described on pages 

“Checking external connections”

 on page

 108 

and 

“Checking internal components”

 on page

 108.

•

If troubleshooting strategies (checking cables and connections, reinstalling system software, and so forth) do not 

solve the problem, and you suspect that the hard disk drive or the motherboard is faulty, always troubleshoot in the 

following order:

•

First, 

replace the hard disk drive and install system software. 

Always replace a faulty hard disk drive with a new hard disk drive. Transferring a hard disk drive from one E-36A 

to another is incorrect and strongly discouraged.

•

If the problem persists,

 reinstall the original hard disk drive in the system, and then replace the motherboard.

Motherboard cautions

•

Do not

 transfer the BIOS chip from the old motherboard onto the new motherboard. 

BIOS chips are not interchangeable. 

Troubleshooting in the wrong order will cause the system to malfunction. In general, it

 is 

highly 

unlikely that both the hard disk drive and the motherboard are defective; therefore, avoid 

replacing both to solve one problem.

If you have exhausted all other troubleshooting remedies and determined that you need to install a 

new motherboard, be sure to observe the following cautions:

Summary of Contents for E-36A


































































































































Reviews:

No comments