manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 22 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 22

22 

Installation and Service Guide: Color Controller E-36A

Installing Hardware

the monitor, keyboard, and mouse, see the documentation that accompanies those products.

1

Make sure that the E-36A is installed in the Fiery NX One Station furniture and the monitor is securely attached to 

the top of the E-36A.

For more information, see documentation provided with the Fiery NX One Station kit.

2

Connect the monitor cable to the Display port on the connector panel. 

3

Connect the monitor power cable to a power outlet on the wall. 

4

Place the keyboard and mouse on the furniture table top. 

5

Connect the wireless adapter for the keyboard and mouse to one of the USB port.

Use the USB ports at the front of the E-36A.

6

Power on the mouse by using the power switch on the bottom side of the mouse.

To connect the E-36A to the power

1

Locate the E-36A power cable that is shipped with the E-36A.

Be sure to use the appropriate power cable for your regional outlet type.

2

Connect the recessed end of the E-36A power cable to the power outlet at the customer site.

3

Connect the other end to the E-36A power connector (see 

Figure  6

).

Connecting to the printer and the network

Connect the E-36A to the printer and the network to enable print and network connectivity.

To connect to the printer

1

Make sure that the E-36A and printer are powered off.

2

Locate the printer interface (crossover Ethernet) cable that is shipped with the E-36A.

The straight-through network cable at the customer site and the crossover Ethernet cable shipped 

with the E-36A look similar, but are not interchangeable. Make sure that you connect the printer 

interface (Crossover Ethernet) cable shipped with the E-36A.

Summary of Contents for E-36A


































































































































Reviews:

No comments