manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 112 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 112

112 

Installation and Service Guide: Color Controller E-36A

Troubleshooting

Fan is:

•

Properly positioned (not backwards)

•

Installed in the correct connector

•

Not visibly damaged (fan, fan cable, cable connector, 
and

 motherboard

 connector)

Fans, 

page

 75

.

The power supply is:

•

Present

•

Correctly installed

•

Not visibly damaged

Cable connectors are:

•

Firmly connected

•

Not visibly damaged

•

Installed in the correct devices

Power supply, 

page

 77

.

The hard disk drive is:

•

Present

•

Correctly installed

•

Not visibly damaged

Hard disk drive data cables are:

•

Present

•

Firmly connected to the correct SATA connectors on the motherboard 
(see 

page

 58

)

•

Not visibly damaged

Hard disk drive power cables are:

•

Present

•

Firmly connected to the SATA power connectors on the hard disk 
drives. 

•

Not visibly damaged

Hard disk drive, 

page

 79

.

.

Each cable required is:

•

Present

•

Installed in the correct connector

•

Well-seated

•

Not visibly damaged (cable or connector)

HDD data cable, 

page

 79

.

Power supply cable, 

page

 77

.

If included in the system, the required mouse, monitor, and keyboard are 
present and appear undamaged. The mouse and keyboard are connected 
to the correct ports on the E-36A connector panel.

The cables required are:

•

Present

•

Installed in the correct connector

•

Well-seated

•

Not visibly damaged (cable or connectors)

For the following items, see the documentation that 
accompanies the package.

•

Mouse,

 

page

 21

.

•

Monitor, 

page

 21

.

•

Keyboard, 

page

 21

.

•

Monitor power cord.

Conditions to verify

Part and additional page references

Summary of Contents for E-36A


































































































































Reviews:

No comments