manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 36 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 36

36 

Installation and Service Guide: Color Controller E-36A

Using the E-36A

Quick launch

From the Home screen, you can press the 

Quick launch

 icon on the bottom-left corner of the screen to access the 

following menus:

•

Fiery System Restore

•

Settings

•

About Fiery

•

Print

•

Motherboard replacement (The Motherboard replacement application icon appears when you insert the 

motherboard replacement dongle.)

Figure 16:

Quick launch menu

Pressing the 

Home

 icon takes you back to the Home screen. Before accessing Fiery System Restore or Settings, you 

must log in as an administrator.

For more information on backing up and restoring the E-36A, see

“Using Fiery System Restore”

 on page

 90.

Quick options

The Quick Options menu can be accessed by pressing the three-dot icon on the top-right corner of the Home screen. 

Quick Options provide the following general system settings:

•

Shutdown system: shuts down all Fiery server software and powers off the system.

•

Reboot system: shuts down all Fiery server software and reboots the system.

•

Restart server: resets the Fiery server software, but does not reboot the entire system.

Summary of Contents for E-36A


































































































































Reviews:

No comments