manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 88 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 88

88 

Installation and Service Guide: Color Controller E-36A

Performing Backup and Restore

When backing up an existing E-36A installation

•

For an existing E-36A installation, first check if a backup image exists either on the server or an external location.

•

If a backup image exists, check if it is up to date. Compare the date stamp of the existing backup image to the 

date of the last patch installation. See the system update log for patch information. See 

“System Update Log”

 on 

page

 106.

•

If a backup image does not exist, create a new one after installing all available software updates. 

•

You can save the backup image to any of the following locations:

•

Local HDD

•

USB storage device

For information about requirements of the USB storage device, see the instructions provided on 

page

 92

.

•

Network

•

If you do not have a backup with the system settings and jobs, the system can access a preinstalled recovery backup 

on the HDD provided with the E-36A. See 

“To restore the backup image”

 on page

 92. 

•

If you have a system backup that includes your settings and jobs, you can restore the backup you have created with 

Fiery System Restore. See 

“To restore the backup image”

 on page

 92.

•

Use a descriptive and consistent naming convention when saving image files (such as date, product name, product 

version, and short description).

Backing up the system configuration

If you back up the system configuration, you can restore that configuration after reinstalling or upgrading system 

software. When you back up the system configuration, you save a configuration file that includes one or more of the 

following: 

•

Fiery System Settings

•

Color Settings

•

Scan Settings

•

FreeForm/VDP resources

•

Paper Catalog

•

Virtual Printers

If you restore the system using the preinstalled recovery backup, the system and configuration 

will be reset to the factory default.

Backed up data can be only restored to the same E-36A.

Summary of Contents for E-36A


































































































































Reviews:

No comments