manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 21 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 21

21 

Installation and Service Guide: Color Controller E-36A

Installing Hardware

Following are the E-36A front and connector panel illustrations.

Figure 6:

E-36A front and connector panel

To connect the monitor, keyboard and mouse (Optional).

Note:

 

Monitor, keyboard, and mouse are included with the optional Fiery NX One Station kit. For information about 

Front panel

Connector panel

1

Fiery QuickTouch LCD

5

Type A USB2.0 ports (x2)

2

Type A USB 3.0 ports (x3)

6

Network port (upper RJ-45)

3

Reset button

7

Display port

4

Power button

8

Type A USB2.0 ports (x2)

Note:

 

Do not use the USB ports on the Fiery QuickTouch 

for keyboard/mouse connections for the service purpose.

Note:

 

Unlabeled connectors/ports are not used.

9

Type A USB3.0 ports (x2) 

10

Printer interface (Crossover Ethernet) cable port (Lower RJ-45)

11

Type B USB port for power synchronization 

12

OFF/ON switch for power synchronization

OFF: Left

ON: Right

13

Cover

14

Power connector

15

Power switch

|: Power On 

O: Power Off

15

1

4

2

3

8

14

5

12

6

7

9

10

11

13

Summary of Contents for E-36A


































































































































Reviews:

No comments