manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 94 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 94

94 

Installation and Service Guide: Color Controller E-36A

Performing Backup and Restore

Erase data from hard disk drive(s)

If selected, the following methods are provided:

•

Randomized erase for writing random data to all disk sectors before writing zero.

•

Quick erase for writing zeroes to all disk sectors.

Advanced backup management

Allows the Administrator to:

•

Load backup settings from a USB drive to apply to system backup images.

•

Save or restore backup history files.

•

Search for backup images created on a replaced system to be applied to the current one.

Launch Windows Task Manager

Starts the Windows Task Manager. Windows Task Manager displays the programs, processes, and services that are 

currently running on the E-36A. You can use Windows Task Manager to monitor performance or to close a program 

that is not responding.

Summary of Contents for E-36A


































































































































Reviews:

No comments