manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 65 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 65

65 

Installation and Service Guide: Color Controller E-36A

Replacing Parts

5

If you replaced the motherboard with a new motherboard, do the following:

•

Remove the battery (see 

page

 74

).

•

Wait two minutes to allow the motherboard electrical components to fully discharge.

•

Reinstall the battery (see 

page

 74

).

•

Reassemble the E-36A and verify its functionality (see 

page

 83

).

•

Reset the time and date in Setup (see 

page

 74

). 

Verifying new motherboard installation, and transferring options and BIOS information

After you install a new motherboard and reassemble the system, do the following:

•

Verify all functionality by using the motherboard replacement dongle to enter Service Mode. (Service Mode is not 

indicated on the monitor or Fiery QuickTouch, but is entered once you power on with a new motherboard installed 

and the motherboard replacement dongle installed on a USB port.)

Service Mode is a temporary state that allows you to make sure that the motherboard solves the problem that you 

are troubleshooting. Service Mode is exited automatically when you expend the motherboard replacement dongle 

to transfer options to the new motherboard (see 

“Entering Service Mode”

 on page

 65).

•

If the new motherboard solves the problem that you are troubleshooting, use the motherboard replacement dongle 

to transfer options to the new motherboard.

If you determine while in Service Mode that the problem you are troubleshooting was not fixed by installing a new 

motherboard, do not expend the motherboard replacement dongle to transfer options to the new motherboard 

(described below), do not install system software, and do not replace the hard disk drive. Reinstall the old 

motherboard and return the new motherboard and the unused motherboard replacement dongle to inventory. You 

may then perform additional service and troubleshooting procedures.

Transferring options expends the motherboard replacement dongle. For details, see 

“Entering Service Mode”

 on 

page

 65. 

Entering Service Mode

Use the following procedure to verify that the system functions properly after installing a new motherboard.

To enter Service Mode and verify the system

Note:

 

This procedure assumes that the E-36A is powered off, you have installed a new motherboard, and that you have 

reassembled the E-36A and attached external cables.

1

Make sure the E-36A is connected to the printer.

Do not transfer options to the new motherboard prematurely. Do so only after you verify the new 

motherboard in Service Mode. Remember that once options are transferred to the new 

motherboard using the motherboard replacement dongle, the motherboard is customized and 

cannot be used in another system.

Summary of Contents for E-36A


































































































































Reviews:

No comments