manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 93 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 93

93 

Installation and Service Guide: Color Controller E-36A

Performing Backup and Restore

4

Select one of the following restore options:

•

Restore from a local image

•

Restore from a USB storage device

•

Restore from the factory default image

5

Click 

Continue.

6

Follow the on-screen prompts to restore the backup image.

Note:

 

The E-36A must remain powered ON during the backup or restore process.

To restore the system by booting from a bootable USB storage device

•

Follow the instructions described in 

“To restore the system from bootable USB storage device”

 on page

 93.

Using bootable USB storage device to restore

Use the following procedure when the E-36A does not boot from the built-in hard disk drive.

You can restore from the bootable USB storage device (including the Fiery factory image) created by Fiery System 

Restore.

To restore the system from bootable USB storage device

To restore from the bootable media, you must have created a backup media. If you have created a backup as bootable 

backup media, follow these instructions. You can use this procedure to install the system software after you replaced 

the new hard disk drive. 

1

Shut down the E-36A.

2

Attach the bootable USB storage device to the E-36A. 

Be sure to not attach other USB devices to the E-36A.

3

Press the power button to turn on the E-36A.

The E-36A will boot from the bootable USB storage device.

4

Follow the instructions on the Fiery QuickTouch display or the monitor (if available) to restore the backup image.

Platform Utilities

Following utilities are available when you select 

Platform Utilities

.

•

Erasing hard disks

•

Advanced backup management

•

Launching Windows Task Manager

Note:

 

The 

Platform Utilities

 is available only on the monitor. 

Summary of Contents for E-36A


































































































































Reviews:

No comments