Danfoss VLT Automation VT Drive FC 322 Programming Manual Download | Manualshive

Page: 199 / 304

background image

2.17 Main Menu - Extended Closed Loop - Group 21

2.18.1 21-** Ext. Closed Loop

The offers 3 Extended Closed Loop PID controllers in addition to the PID Controller. These can be configured independently to control either external

actuators (valves, dampers etc.) or be used together with the internal PID Controller to improve the dynamic responses to setpoint changes or load

disturbances.

The Extended Closed Loop PID controllers may be interconnected or connected to the PID Closed Loop controller to form a dual loop configuration.

In order to control a modulating device (e.g. a valve motor), this device must be a positioning servo motor with built-in electronics accepting either a

0-10V (signal from Analog I/O card MCB 109) or a 0/4-20 mA (signal from Control Card and/or General Purpose I/O card MCB 101) control signal.

The output function can be programmed in the following parameters:

•

Control Card, terminal 42: par. 6-50

Terminal 42 Output

(setting [113]...[115] or [149]...[151], Ext. Closed Loop 1/2/3

•

General Purpose I/O card MCB 101, terminal X30/8: par. 6-60

Terminal X30/8 Output

, (setting [113]...[115] or [149]...[151], Ext. Closed Loop

1/2/3

•

Analog I/O card MCB 109, terminal X42/7...11: par. 26-40

Terminal X42/7 Output

, par. 26-50

Terminal X42/9 Output

, par. 26-60

Terminal X42/11

Output

(setting [113]...[115], Ext. Closed Loop 1/2/3

General Purpose I/O card and Analog I/O card are optional cards.

2.18.2 21-0* Extended CL autotuning

The extended PID Closed Loop PID controllers (

par. 21-**, Ext. Closed Loop

) can each be auto-tuned, simplifying and saving time during commissioning,

whilst ensuring accurate PID control adjustment.

To use PID autotuning it is necessary for the relevant Extended PID controller to have been configured for the application.

A graphical Local Control Panel (LCP) must be used in order to react on messages during the autotuning sequence.

Enabling autotuning par. 21-09

PID Auto Tuning

puts the relevant PID controller into PID autotuning mode. The LCP then directs the user with on-screen

instructions.

PID autotuning functions by introducing step changes and then monitoring the feedback. From the feedback response, the required values for PID

Proportional Gain, par. 21-21

Ext. 1 Proportional Gain

for EXT CL 1, par. 21-41

Ext. 2 Proportional Gain

for EXT CL 2 and par. 21-61

Ext. 3 Proportional

Gain

for EXT CL 3 and Integral Time, par. 21-22

Ext. 1 Integral Time

for EXT CL 1, par. 21-42

Ext. 2 Integral Time

for EXT CL 2 and par. 21-62

Ext. 3

Integral Time

for EXT CL 3 are calculated. PID Differentiation Time, par. 21-23

Ext. 1 Differentation Time

for EXT CL 1, par. 21-43

Ext. 2 Differentation

Time

for EXT CL 2 and par. 21-63

Ext. 3 Differentation Time

for EXT CL 3 are set to value 0 (zero). Normal / Inverse, par. 21-20

Ext. 1 Normal/Inverse

Control

for EXT CL 1, par. 21-40

Ext. 2 Normal/Inverse Control

for EXT CL 2 and par. 21-60

Ext. 3 Normal/Inverse Control

for EXT CL 3 are determined

during the tuning process.

These calculated values are presented on the LCP and the user can decide whether to accept or reject them. Once accepted, the values are written to

the relevant parameters and PID autotuning mode is disabled in par. 21-09

PID Auto Tuning

. Depending on the system being controlled the time required

to carry out PID autotuning could be several minutes.

Excessive feedback sensor noise should be removed using the input filter (parameter groups 6-**,5-5* and 26-**, Terminal 53/54 Filter Time Constant/

Pulse Filter Time Constant #29/33) before activating PID autotuning.

VLT

p

Automation VT Drive FC322

Programming Guide

2 Parameter Description

MG.20.W1.22 - VLT

p

is a registered Danfoss trademark

197

2

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20772-Danfoss-131X8135-VLT-Automation-VT-Drive-VFD-FC322-230V-5-HP.aspx

«
...
197
198
199
200
201
...
»

Summary of Contents for VLT Automation VT Drive FC 322

















































































































































































































































































































Reviews:

No comments

Related manuals for VLT Automation VT Drive FC 322

Brand: Parker Pages: 30

Brand: VAT Pages: 22

Brand: Aalborg Pages: 15

Brand: Aalborg Pages: 48

medialon Showmaster Go

Brand: 7th Sense Pages: 2

Brand: Jeep Pages: 32

Brand: Accel Pages: 8

Brand: Samson Pages: 48

Brand: Parker Pages: 28

Brand: u-blox Pages: 28

Brand: u-blox Pages: 2

Brand: Vizio Pages: 65

Brand: Dantel Pages: 6

GAMMA VERSUS Series

Brand: JCM Pages: 111

767-4804/000-800

Brand: WAGO Pages: 80

Optidrive Elevator

Brand: Invertek Pages: 5

Brand: Techtrol Pages: 4

Brand: HEROSE Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands