Cypress PSoC CY8C23533 Technical Reference Manual Download | Manualshive

Page: 127 / 410

background image

Document # 001-20559 Rev. *D

63

0,2Bh

13.2.15

DCBxxCR0

(UART Receiver Control)

Digital Communication Type B Block Control Register 0

This register is the Control register for a UART receiver, if the

register is configured as a ‘101’.

Refer to the

DxBxxDR0 register on page 53

for naming convention and digital row availability information. For additional infor-

mation, refer to the

“Register Definitions” on page 187

in the Digital Blocks chapter. For the Transmit mode definition, refer to

section 13.2.14 on page 62.

7

Parity Error

0

Indicates that no parity error has occurred.

1

Valid when RX Reg Full is set, indicating that a parity error has occurred in the received
byte and cleared on a read of this (CR0) register.

6

Overrun

0

Indicates that no overrun has occurred.

1

Valid when RX Reg Full is set, indicating that the byte in the RX Buffer register has not been
read before the next byte is loaded. It is cleared on a read of this (CR0) register.

5

Framing Error

0

Indicates no framing error has occurred.

1

Valid when RX Reg Full is set, indicating that a framing error has occurred (a logic 0 was
sampled at the STOP bit, instead of the expected logic 1). It is cleared on a read of this
(CR0) register.

4

RX Active

0

Indicates that no reception is in progress.

1

Indicates that a reception is in progress. It is set by the detection of a START bit and
cleared at the

of the STOP bit.

3

RX Reg Full

0

Indicates that the RX Buffer register is empty.

1

Indicates that a byte is received and transferred to the RX Buffer (DR2) register. This bit is
cleared when the RX Buffer register (DR2) is read by the CPU. Interrupt source.

2

Parity Type

0

Even parity.

1

Odd parity.

1

Parity Enable

0

Parity is not enabled.

1

Parity is enabled, frame includes parity bit.

0

Enable

0

Serial Receiver is not enabled.

1

Serial Receiver is enabled.

Individual Register Names and Addresses:

0,2Bh

DCB02CR0: 0,2Bh

DCB03CR0: 0,2Fh

7

6

5

4

3

2

1

0

Access : POR

R : 0

R : 0

R : 0

R : 0

R : 0

RW : 0

RW : 0

RW : 0

Bit Name

Parity Error

Overrun

Framing Error

RX Active

RX Reg Full

Parity Type

Parity Enable

Enable

Bit

Name

Description

«
...
125
126
127
128
129
...
»

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for PSoC CY8C23533

Brand: IEI Technology Pages: 8

Brand: Arbor Technology Pages: 80

Brand: Kontron Pages: 83

Brand: Data Modul Pages: 111

Brand: JK microsystems Pages: 28

Brand: JK microsystems Pages: 28

Brand: Seco Pages: 32

Brand: Seco Pages: 43

Brand: Seco Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands