manualshive.com logo in svg

Cypress PSoC CY8C23533, Technical Reference Manual

Share
Download
Cypress PSoC CY8C23533 Technical Reference Manual Download Page 134

70

Document # 001-20559 Rev. *D

0,69h

13.2.22

SARADC_CR0

SAR8 ADC Control Register 0 

This register is used to control normal ADC operation and show ADC status. 

In the table above, note that the reserved bit is a grayed table cell and is not described in the bit description section below.
Reserved bits should always be written with a value of ‘0’. For additional information, refer to the 

“Register Definitions” on

page 266

 in the SAR8 ADC Block chapter.

6:3

ADC Channel[3:0]

ADC channel is:
0000

P0[0]

0001

P0[1]

0010

P0[2]

0011

P0[3]

0100

P0[4]

0101

P0[5]

0110

P0[6]

0111

P0[7]

1000

CT1

1001

CT2

2

Data Ready

0

New conversion data is not ready or the conversion data has already been read out. Writing
‘1’ to Start/Busy bit automatically clears bit to ‘0’.

1

ADC has newest conversion data, which has never been read out.

1

Start/Busy

0

ADC has finished the operation. If firmware writes a '1' to this bit it means that firmware trig-
gers the ADC to perform the sample and conversion from the next system clock cycle. If this
bit is already '1' (in ADC conversion mode), the new write of '1' forces the ADC to cancel the
ongoing conversion and restart one new conversion from the next system clock cycle.
When the ADC is set to free running, this signal means start a new ADC conversion. The
ADC then automatically starts the new conversion after it finishes the previous conversion.

1

ADC is busy.

0

ADCEN

The ADC automatically enters low power mode right after it finishes the conversion even in Enable
mode. If the ADC has been disabled, it does not perform any operation.
0

Disable ADC operation.

1

Enable ADC operation.

Individual Register Names and Addresses:

0,69h

SARADC_CR0 : 0,69h

7

6

5

4

3

2

1

0

Access : POR

RW : 00

RW : 1

RC : 0

RC : 0

Bit Name

ADC Channel[3:0]

Data Ready

Start/Busy

ADCEN

Bit

Name

Description

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands