Cypress PSoC CY8C23533 Technical Reference Manual Download | Manualshive

Page: 103 / 410

background image

Document # 001-20559 Rev. *D

39

Sleep and Watchdog

12.4.2

Wake Up Sequence

Once asleep, the only event that can wake the system up is
an interrupt. The Global Interrupt Enable of the CPU flag
register does not need to be set. Any unmasked interrupt
wakes the system up. It is optional for the CPU to actually
take the interrupt after the wake up sequence.

The wake up sequence is synchronized to the 32 kHz clock
for purposes of sequencing a startup delay, to allow the
Flash memory module enough time to power up before the
CPU asserts the first read access. Another reason for the
delay is to allow the IMO, bandgap, and LVD/POR circuits
time to settle before actually being used in the system. As
shown in

, the wake up sequence is as follows.

1. The wake up interrupt occurs and is synchronized by the

negative edge of the 32 kHz clock.

2. At the following positive edge of the 32 kHz clock, the

system-wide PD signal is negated. The Flash memory
module, IMO, and bandgap any POR/LVD circuits are all
powered up to a normal operating state.

3. At the next positive edge of the 32 kHz clock, the values

of the bandgap are settled and sampled.

4. At the following negative edge of the 32 kHz clock (after

about 15



s, nominal) the values of the POR/LVD sig-

nals have settled and are sampled. The BRQ signal is
negated by the sleep logic circuit. On the following CPU
clock, BRA is negated by the CPU and instruction exe-
cution resumes.

The wake up times (interrupt to CPU operational) range
from two to three 32 kHz cycles or 61 - 92



s (nominal).

Figure 12-2. Wake Up Sequence

CLK32K

INT

SLEEP

PD

CPUCLK/

24 Mhz

BRQ

BRA

CPU

Sleep timer or GPIO

interrupt occurs.

CPU is restarted after

75



s (nominal).

(Not to Scale)

BANDGAP

LVD/PPOR

ENABLE

POR/LVD/

BANDGAP

SAMPLE

BANDGAP

Interrupt is double sampled by

32K clock and PD is negated to

system.

SAMPLE

LVD/POR

LVD/PPOR is valid

«
...
101
102
103
104
105
...
»

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for PSoC CY8C23533

SBC81203 Series

Brand: AXIOMTEK Pages: 77

Brand: Giantec Pages: 111

Brand: IEI Technology Pages: 16

Brand: Critical Link Pages: 4

StudioZ RenderRAX

Brand: Intergraph Pages: 60

Brand: Intergraph Pages: 66

StudioZ RenderRAX II

Brand: Intergraph Pages: 6

Brand: Intergraph Pages: 68

DX3-6726-2C-2G-T

Brand: EMAC Pages: 34

Brand: EMAC Pages: 118

gKINO-DMF Series

Brand: IEI Technology Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands