Cypress PSoC CY8C23533 Technical Reference Manual Download | Manualshive

Page: 64 / 410

background image

64

Document # 001-20559 Rev. *D

Interrupt Controller

5.3

Register Definitions

The following registers are associated with the Interrupt Controller and are listed in address order. The register descriptions
have an associated register table showing the bit structure for that register. The bits in the tables that are grayed out are
reserved bits and are not detailed in the register descriptions that follow. Reserved bits should always be written with a value
of ‘0’. For a complete table of Interrupt Controller registers, refer to the

“Summary Table of the Core Registers” on page 32

Depending on the PSoC device you have, only certain bits are accessible to be read or written, such as the INT_CLR0 and
INT_MSK0 registers that are analog column and digital row dependent. The analog column dependent registers have the col-
umn number listed to the right of the Address column. The digital row dependent registers are set up the same way, only with
the term “Row” in the Address column.

5.3.1

INT_CLRx Registers

The Interrupt Clear Registers (INT_CLRx) are used to
enable the individual interrupt sources’ ability to clear posted
interrupts.

There are three interrupt clear registers (INT_CLR0,
INT_CLR1, and INT_CLR3) which may be referred to in
general as INT_CLRx.The INT_CLRx registers are similar to
the INT_MSKx registers in that they hold a bit for each inter-
rupt source. Functionally the INT_CLRx registers are similar
to the INT_VC register, although their operation is com-
pletely independent. When an INT_CLRx register is read,
any bits that are set indicate an interrupt has been posted
for that hardware resource. Therefore, reading these regis-
ters gives the user the ability to determine all posted inter-
rupts.

The Enable Software Interrupt (ENSWINT) bit in
INT_MSK3[7] determines the way an individual bit value
written to an INT_CLR0 register is interpreted. When
ENSWINT is cleared (the default state), writing 1's to an
INT_CLRx register has no effect. However, writing 0's to an
INT_CLRx register, when ENSWINT is cleared, causes the
corresponding interrupt to clear. If the ENSWINT bit is set,
any 0's written to the INT_CLRx registers are ignored. How-
ever, 1's written to an INT_CLRx register, while ENSWINT is
set, causes an interrupt to post for the corresponding inter-
rupt.

Note

When using the INT_CLRx register to post an inter-

rupt, the hardware interrupt source, such as a digital clock,
must not have its interrupt output high. Therefore, it may be
difficult to use software interrupts with interrupt sources that
do not have enables such as VC3.

Software interrupts can aid in debugging interrupt service
routines by eliminating the need to create system level inter-

actions that are sometimes necessary to create a hardware-
only interrupt.

5.3.1.1

INT_CLR0 Register

Bit 7: VC3.

This bit allows posted VC3 interrupts to be

read, cleared, or set.

Bit 6: Sleep.

This bit allows posted sleep interrupts to be

read, cleared, or set.

Bit 5: GPIO.

This bit allows posted GPIO interrupts to be

read, cleared, or set.

Bit 4: SAR8 ADC.

This bit allows posted SAR8 ADC inter-

rupts to be read, cleared, or set.

Bit 3: Analog 2.

This bit allows posted analog column 2

interrupts to be read, cleared, or set.

Bit 2: Analog 1.

This bit allows posted analog column 1

interrupts to be read, cleared, or set.

Bit 1: Analog 0.

This bit allows posted analog column 0

interrupts to be read, cleared, or set.

Bit 0: V Monitor.

This bit allows posted V monitor inter-

rupts to be read, cleared, or set.

For additional information, refer to the

INT_CLR0 register on

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

0,DAh

VC3

Sleep

GPIO

SAR8 ADC

Analog 1

Analog 0

V Monitor

RW : 0

0,DBh

DCB03

DCB02

DBB01

DBB00

RW : 0

0,DDh

I2C

RW : 0

«
...
62
63
64
65
66
...
»

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for PSoC CY8C23533

Brand: EEPD Pages: 111

COM Express Type 7+

Brand: Connect Tech Pages: 30

Brand: Teknor Industrial Computers Pages: 204

Orange Pi 3G-IoT

Brand: Shenzhen Xunlong Software Co., Ltd Pages: 21

Brand: IEI Technology Pages: 146

Brand: Aaeon Pages: 109

AAEON GENE-WHU6

Brand: Asus Pages: 105

Brand: EEPD Pages: 113

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands