manualshive.com logo in svg

Cypress PSoC CY8C23533, Technical Reference Manual

Share
Download
Cypress PSoC CY8C23533 Technical Reference Manual Download Page 265

Document # 001-20559 Rev. *D

201

Digital Blocks

If the width of the PWM low time is reduced to a point where
it is equal to the dead band period, the corresponding
phase, PHI2, disappears altogether. Note that after the ris-
ing edge of the PWM, the opposite phase still has the pro-
grammed dead band. 

Figure 17-12

 shows an example

where the dead band period is two and the PWM width is
two. In this case, the high time of PHI2 is zero clocks. Note
that the phase 1 dead band time is still two clocks.

Figure 17-12.  PWM Width Equal to Dead Band Period 

In the case where the dead band period is greater than the
high or low of the PWM reference, the output of the associ-
ated phase is not asserted high.

17.3.3.2

Kill Operation

It is assumed that the KILL input is not synchronized at the
row input. (This is not a requirement; however, if synchro-
nized, the KILL operation has up to two 24 MHz clock cycles
latency, which is undesirable.) To support the restart modes,
the negation of KILL is internally (in the block) synchronized
to the 24 MHz system clock.

There are three KILL modes supported. In all cases, the
KILL signal asynchronously forces the outputs to logic 0.
The differences in the modes come from how dead band
processing is restarted. 
1.

Synchronous Restart Mode

: When KILL is asserted 

high, the internal state is held in reset and the initial dead 
band period is reloaded into the counter. While KILL is 
held high, incoming PWM reference edges are ignored. 
When KILL is negated, the next incoming PWM refer-
ence edge restarts dead band processing. See 

Figure 17-13

.

2.

Asynchronous Restart Mode

: When KILL is asserted 

high, the internal state is not affected. When KILL is 
negated, the outputs are restored, subject to a minimum 
disable time between one-half and one and one-half 
clock cycle. See 

Figure 17-14

.

3.

Disable Mode

: There is no specific timing associated 

with this mode. The block is disabled and the user must 
re-enable the function in firmware to continue process-
ing. 

Figure 17-13.  Synchronous Restart KILL Mode

Figure 17-14.  Asynchronous Restart Kill Mode 

CLK

PWM

PHI1

PHI2

2

2

2

PWM 

REFERENCE

PHI2

PHI1

KILL

Short KILL, outputs off for 

remainder of current cycle.  

Operation resumes on 

the next PWM edge. 

PWM 

REFERENCE

PHI2

PHI1

KILL

Output is off for duration 

of KILL on time.  

These edges 

are skipped.

Operation resumes

on this edge.

PWM 

REFERENCE

PHI2

PHI1

KILL

Outputs are forced low only as 

long as the KILL is asserted, 

subject to the minimum disable 

time.  Internal operation is 

unaffected.

PWM 

REFERENCE

PHI2

PHI1

KILL

Outputs are disabled 

immediately on KILL.

Minimum disable time 

is between ½ and 1½  

block clock cycle.

PHI1 or PHI2

KILL

BLOCK CLK

Example of KILL shorter 
than the minimum.

Example of KILL longer 
than the minimum.

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands