Cypress PSoC CY8C23533 Technical Reference Manual Download | Manualshive

Page: 313 / 410

background image

Document # 001-20559 Rev. *D

249

22.

Continuous Time PSoC Block

This chapter discusses the Analog Continuous Time PSoC Block and its associated registers. This block supports program-
mable

attenuation

opamp circuits; instrumentation amplifiers, using two CT blocks (differential gain); and modest

response-time analog comparators. For a complete table of the Continuous Time PSoC Block registers, refer to the

mary Table of the Analog Registers” on page 217

. For a quick reference of all PSoC registers in address order, refer to the

Register Details chapter on page 47

22.1

Architectural Description

The Analog Continuous Time blocks are built around a rail-
to-rail input and output, low offset, low

opamp. There

are several analog multiplexers (muxes) controlled by regis-
ter bit settings in the control registers that determine the sig-
nal topology inside the block. There is also a precision
resistor string located in the feedback path of the opamp,
which is controlled by register bit settings.

The block also contains a low power comparator, connected
to the same inputs and outputs as the main amplifier. This
comparator is useful for providing a digital compare output in
low power sleep modes, when the main amplifier is powered
off.

There are three discrete outputs from this block. These out-
puts connect to the following buses:
1. The analog output bus (ABUS), which is an analog bus

resource shared by all of the analog blocks in the analog
column. This signal may also be routed externally
through an output buffer.

2. The comparator bus (CBUS), which is a digital bus

resource shared by all of the analog blocks in the analog
column.

3. The local output buses (OUT, GOUT, and LOUT), which

are routed to neighboring blocks. GOUT and LOUT refer
to the gain/loss mode configuration of the block and con-
nect to GIN/LIN inputs of neighboring blocks.

«
...
311
312
313
314
315
...
»

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for PSoC CY8C23533

Brand: Raspberry Pi Pages: 2

Brand: AAON Pages: 18

Brand: Ebyte Pages: 16

ETHERIOS ConnectCore 6

Brand: Digi Pages: 15

ROCKY-P218BXA Pentium II & Creative Sound

Brand: ICP Electronics Pages: 39

Brand: IEI Technology Pages: 234

Brand: IBASE Technology Pages: 81

SCP-P4040-4G-ENP2

Brand: SMART Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands