manualshive.com logo in svg

Cypress PSoC CY8C23533, Technical Reference Manual

Share
Download
Cypress PSoC CY8C23533 Technical Reference Manual Download Page 122

58

Document # 001-20559 Rev. *D

0,23h

13.2.10

DxBxxCR0 

(Dead Band Control)

 

Digital Basic/Communication Type B Block Control Register 0 

 

This register is the Control register for a dead band, if the 

DxBxxFN

 register is configured as a ‘100’.

Refer to the 

DxBxxDR0 register on page 53

 for naming convention and digital row availability information. In the table above,

note that reserved bits are grayed table cells and are not described in the bit description section below. Reserved bits should
always be written with a value of ‘0’. For additional information, refer to the 

“Register Definitions” on page 187

 in the Digital

Blocks chapter.

2

Bit Bang Clock

When Bit Bang mode is enabled, the output of this register bit is substituted for the PWM reference.
This register may be toggled by user firmware to generate PHI1 and PH2 output clocks with the pro-
grammed dead time.

1

Bit Bang Mode

0

Dead Band Generator uses the previous block primary output as the input reference.

1

Dead Band Generator uses the Bit Bang Clock register as the input reference.

0

Enable

0

Dead Band Generator is not enabled.

1

Dead Band Generator is enabled.

Individual Register Names and Addresses:

0,23h

DBB00CR0: 0,23h

DBB01CR0: 0,27h

DCB02CR0: 0,2Bh

DCB03CR0: 0,2Fh

7

6

5

4

3

2

1

0

Access : POR

RW : 0

RW : 0

RW : 0

Bit Name

Bit Bang Clock

Bit Bang Mode

Enable

Bit

Name

Description

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands