manualshive.com logo in svg

Cypress PSoC CY8C23533, Technical Reference Manual

Share
Download
Cypress PSoC CY8C23533 Technical Reference Manual Download Page 324

260

Document # 001-20559 Rev. *D

Switched Capacitor PSoC Block

23.3.2

ASCxxCR1 Register 

The Analog Switch Cap Type C Block Control Register 1
(ASCxxCR1) is one of four registers used to configure a
type C switch capacitor PSoC block.

Bits 7 to 5: ACMUX[2:0].  

These bits control the input mux-

ing for both the A and C capacitor branches. The high order
bit, ACMux[2], selects one of two inputs for the C branch.

Bits 4 to 0: BCap[4:0].  

The BCap bits set the value of the

capacitor in the B path. 

For additional information, refer to the 

ASCxxCR1 register

on page 84

.

23.3.3

ASCxxCR2 Register 

The Analog Switch Cap Type C Block Control Register 2
(ASCxxCR2) is one of four registers used to configure a
type C switch capacitor PSoC block.

Bit 7: AnalogBus.  

This bit gates the output to the analog

column bus (ABUS). The output on the ABUS is affected by
the state of the ClockPhase bit in the Control 0 register. If
AnalogBus is set to ‘0’, the output to the analog column bus
is tri-stated. If AnalogBus is set to ‘1’, the signal that is out-
put to the analog column bus is selected by the ClockPhase
bit. If the ClockPhase bit is ‘0’, the block output is gated by
sampling clock on the last part of PHI2. If the ClockPhase bit
is ‘1’, the block output continuously drives the ABUS.

Bit 6: CompBus.  

This bit controls the output to the column

comparator bus (CBUS). Note that if the CBUS is not driven
by anything in the column, it is pulled low. The comparator
output is evaluated on the rising edge of internal PHI1 and is
latched so it is available during internal PHI2.

Bit 5: AutoZero.  

This bit controls the shorting of the output

to the inverting input of the opamp. When shorted, the
opamp is basically a follower. The output is the opamp off-
set. By using the feedback capacitor of the integrator, the
block can memorize the offset and create an offset cancella-
tion scheme. AutoZero also controls a pair of switches
between the A and B branches and the summing node of
the opamp. If AutoZero is enabled, then the pair of switches
is active. AutoZero also affects the function of the FSW1 bit
in the Control 3 register.

Bits 4 to 0: CCap[4:0].  

The CCap bits set the value of the

capacitor in the C path. 

For additional information, refer to the 

ASCxxCR2 register

on page 85

.

Add.

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

x,95h

ASC21CR1

ACMux[2:0]

BCap[4:0]

RW : 00

LEGEND

x

An “x” before the comma in the address field indicates that the register exists in both register banks.

Add.

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

x,96h

ASC21CR2

AnalogBus

CompBus

AutoZero

CCap[4:0]

RW : 00

LEGEND

x

An “x” before the comma in the address field indicates that the register exists in both register banks.

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands