manualshive.com logo in svg

Avaya programming and use, Installation And Use Manual, Page: 46 / 468

Share
Download
Avaya programming and use Installation And Use Manual Download Page 46

PARTNER

®

 Advanced Communications System Installation, Programming, and Use

Installing the Control Unit

2-14

4.

Press the power cord firmly into the power jack on 
the carrier or the stand-alone processor module 
until the cord locks into place (see 

Figure 2-16

).

5.

Plug the other end of the power cord into a 
properly grounded three-prong wall outlet that is 
not controlled by a switch.

6.

If you have a 5-slot carrier, move the On/Off 
switch to the On (“—”) position.

CAUTION:

The power cord should hang straight down from 
the connector for the entire length of the module 
or carrier. Do not install the power cord at an 
angle to the case or with a loop in it.

7.

If this is the initial installation for a Release 3.0 
system, follow these additional steps:

a.

Check the LEDs to make sure that the 
processor is on steady green for at least 
15 seconds.

b.

Press 

f00ss#
989

 at extension 10 or 11.

c.

Press 

25327

.

The system resets. You may proceed with 
the rest of the installation upon 
completion of the reset (about 20 
seconds).

Figure 2-16. Attaching the Power 

Cord

Stand-Alone 

2-Slot

5-Slot

Summary of Contents for programming and use





















































































































































































































































































































































































































































































Reviews:

No comments