Avaya programming and use, Installation And Use Manual, Page: 442 / 468

PARTNER
®
Advanced Communications System Installation, Programming, and Use
E-2
System Flow Chart—System
Outgoing Call Restriction
Button
Dial
#114
Dial 1=Assigned
2=Not Assigned
3=Select Button then press a
programmable button
System Date
Dial
#101
Dial the date (MMDDYY)
Number of Lines
Dial
#104
Dial two digits (01-31) (R4 or later), or
Dial two digits (01-19) (Prior to R4),
for # of outside lines assigned to every
extension. 3 per ACS processor &
308EC module. 16 per T1 or 1600 DSL
module. 2 per 206 or 200 module
. 4
per 400 module
WARNING
Do not use Number of Lines (#104) after
initial setup. In Key mode, the Number of
lines procedure will change Line
Assignment (#301), Line Access
Restriction (#302), Automatic Line
Selection and Line Ringing to factory
settings
To change line assignments without
affecting other settings, use Line
Assignment (#301)
In Hybrid mode, the Number of Lines
procedure will change Pool Line
Assignment (#207), Pool Extension
Assignment (#314), and Pool Access
Restriction (#315). Additionally, it
changes Line Assignment (#301), Line
Access Restriction (#302), Automatic
Line Selection and Line Ringing. To
change pool assignments without
affecting other settings, use Pool Line
Assignment (#207) and Pool Extension
Assignment (#314)
System Time
Dial
#103
Dial the time (HHMM-24 hr. military time)
System Day
Dial
#102
Dial 1=Sun
2=Mon 3-Tue, 4=Wed, 5=Thur, 6=Fri,
7=Sat
2.0 or earlier
Transfer Return Rings
Dial
#105
Dial 1 digit (0-9) for # of rings before call
returns.
0-9 rings
4 rings
Recall Timer Durations
Dial
#107
Dial two digits (01-80) to set length of a
switchook flash
=18 (450 msec)
Rotary Dialing Timeout
Dial
#108
Dial 1=4 secs
2=8 secs
3=12 secs
Outside Conference Denial
Dial
#109
Dial 1=Allowed
2=Disallowed
Automatic System Answer Delay
Dial
#110
Dial a ring delay number (0-9)
2 rings
Automatic System Answer Button
Dial
#111
Dial 1=Assigned
2=Not Assigned
3=Select Button then press a
programmable button
2.0
2.0
Mode of Operation
Press
f00s
s#198
Enter the system password
Dial 1=Key (factory setting)
2=Hybrid
VMS Cover Rings
Dial
#117
Dial 1-9
3
Wake Up Service Button
Dial
#115
Dial 1=Assigned
2=Not Assigned
3=Select Button then press a
programmable button
Call Coverage Rings
Dial
#116
Dial 1-9
2
2.0 only
Direct Extension Dial Delay
Dial
#112
Dial a ring delay number (0-9),
2 rings
0 rings=answered immediately
Ring On Transfer
Dial
#119
Dial 1= Active
2=Not Active
Automatic System Answer Mode
Dial
#121
Dial 1=Hold
2=Disconnect
3=Ring
Caller ID Type
Dial
#122
Dial 1=USA
2=Singapore
Backup Programming Automatic
Dial
#123
Dial 1=Active
2=Not Active
3=Backup Alarm Cleared
Backup Programming—Manual
Dial
#124
Press
e
to begin the backup
Automatic Daylight/ Standard Times
Dial
#126
Dial 1=Active
2=Not Active
Restore Programming
Dial
#125
Dial 1= MAN.mmddyy
2=AUTO.mmddyy
Press
e
to begin the restore
System Reset—Programming Saved
IMPORTANT: Using this procedure
disconnects any active calls but retains
system settings. Use it only if the
system fails to function correctly after a
power failure or down period.
Dial
#728
Direct Extension Dial Button
Dial
#113
Dial 1=Assigned,
2=Not Assigned
3=Select Button then press a
programmable button
2.0
2.0
3.0
Hold Reminder Tone
Dial
#127
Dial 0=Not Active
1=10 seconds
2=20 seconds
3=30 seconds
4=45 seconds
5=60 seconds
6=90 seconds
7=120 seconds
8=150 seconds
9=180 seconds
6.0