Amada ML-2350A-CE, Operation Manual, Page: 81 / 235

1. Setting Welding Schedules
81
ML-2350A/2351A
Chapter 2 V
arious Settings
Introduction Part
Inst
allat
ion and Preparation Part
Operating Part
Maintenance Part
Appendixes
1
Setting Output Schedules by Flexible Waveform (FLEX)
Set the output time and output value of each POINT in the range of "POINT 01"
to "POINT 20" by "FLEX" and set the laser light output that becomes a flexible
waveform.
In this example, SCHEDULE No.: #01, peak value: 7.0 kW, POINT 01: 1.0 ms/90%,
POINT 02: 1.0 ms/70%, POINT 03: 1.0 ms/88%, POINT 04: 1.0 ms/65%, and POINT
05: 1.0 ms/0% are set as output schedules.
(1) Press the "SCHED" button to display the SCHEDULE screen.
(2) Press the "SCHEDULE" setting button.
Enter the SCHEDULE number.
(3) Press the "FORM" button to set "FLEX."
(4) Press the "PEAK POWER" setting button.
Enter the laser output peak value.
<Note>
The settable maximum peak value of laser output differs depending on the model.
ML-2350A: 7.0 kW / ML-2351A: 5.0 kW
(5) Press the laser output time "TIME [ms]" and laser output value "POWER [%]"
setting buttons of "POINT 01" to "POINT 05."
Enter the respective value.
⇒
When the button of POINT is pressed, the POINT display column is
scrolled to the right and left so as to display a POINT that is not yet displayed.
⇒
Set the point in the range of "POINT 01" to "POINT 20" and the laser output
time in the range of 0.1 to 30.0 ms. For the laser output value, set the ratio (%)
supposing that the set laser output peak value is 100%.
<Note>
For setting the laser output time, enter the time from the previous POINT.
Set the laser output time so as to result in the following value.
0.25 ms ≤ Total of all POINT values ≤ 30.0 ms (90.0 ms when the time of 0% is
included in the output value)
(6) To output laser light several times for one second, press the "REPEAT" setting
button and set the laser light output count for one second in the range of 000 to
200 pps (pulse per second).
⇒
When 0 is set, a single output is performed.
1
Setting Output Schedules by Flexible Waveform (FLEX)
Set the output time and output value of each POINT in the range of "POINT 01"
to "POINT 20" by "FLEX" and set the laser light output that becomes a flexible
waveform.
In this example, SCHEDULE No.: #01, peak value: 7.0 kW, POINT 01: 1.0 ms/90%,
POINT 02: 1.0 ms/70%, POINT 03: 1.0 ms/88%, POINT 04: 1.0 ms/65%, and POINT
05: 1.0 ms/0% are set as output schedules.
(1) Press the "SCHED" button to display the SCHEDULE screen.
(2) Press the "SCHEDULE" setting button.
Enter the SCHEDULE number.
(3) Press the "FORM" button to set "FLEX."
(4) Press the "PEAK POWER" setting button.
Enter the laser output peak value.
<Note>
The settable maximum peak value of laser output differs depending on the model.
ML-2350A: 7.0 kW / ML-2351A: 5.0 kW
(5) Press the laser output time "TIME [ms]" and laser output value "POWER [%]"
setting buttons of "POINT 01" to "POINT 05."
Enter the respective value.
⇒
When the button of POINT is pressed, the POINT display column is
scrolled to the right and left so as to display a POINT that is not yet displayed.
⇒
Set the point in the range of "POINT 01" to "POINT 20" and the laser output
time in the range of 0.1 to 30.0 ms. For the laser output value, set the ratio (%)
supposing that the set laser output peak value is 100%.
<Note>
For setting the laser output time, enter the time from the previous POINT.
Set the laser output time so as to result in the following value.
0.25 ms ≤ Total of all POINT values ≤ 30.0 ms (90.0 ms when the time of 0% is
included in the output value)
(6) To output laser light several times for one second, press the "REPEAT" setting
button and set the laser light output count for one second in the range of 000 to
200 pps (pulse per second).
⇒
When 0 is set, a single output is performed.