ABB ACQ810 Firmware Manual Download Page 110

Page: 110 / 376

110 Parameters

Summary of parameter groups

Group

Contents

Page

01 Actual values

Basic signals for monitoring of the drive.

112

02 I/O values

Input and output states and values; control and status words.

113

03 Control values

Speed and torque control values.

123

04 Appl values

Process and counter values.

123

05 Pump values

Pump station actual values.

Alarm and fault information.

131

09 System info

Drive type, program revision and option slot occupation information.

134

10 Start/stop/dir

Start/stop/direction, run enable and emergency stop source selections;
start inhibit and start interlock configuration.

135

11 Start/stop mode

Start and stop modes; magnetization settings; DC hold configuration.

140

12 Operating mode

Selection of external control location and EXT2 operating mode.

141

13 Analogue inputs

Analog input signal processing.

142

14 Digital I/O

Configuration of digital input/outputs, relay outputs, the frequency input,
and the frequency output.

148

15 Analogue outputs

Selection and processing of actual signals to be indicated through the
analog outputs.

158

16 System

Local lock and parameter lock settings; parameter restore; user
parameter set load/save; parameter change log reset; parameter list
settings; unit of power selection; application macro display.

164

19 Speed calculation

Speed scaling, feedback and supervision settings.

167

20 Limits

Drive operation limits.

170

21 Speed ref

Speed reference source selection and processing.

172

22 Speed ref ramp

Speed reference and emergency stop (OFF3) ramp settings.

173

23 Speed ctrl

Speed controller settings.

176

25 Critical speed

Configuration of critical speeds (or ranges of speed) that are avoided
due to, for example, mechanical resonance problems.

184

26 Constant speeds

Constant speed selection and values.

185

27 Process PID

Configuration of process PID control.

187

28 Procact sel

Process actual value (feedback) settings.

191

29 Setpoint sel

Process setpoint (reference) settings.

193

30 Fault functions

Configuration of behavior of the drive upon various fault situations.

195

31 Motor therm prot

Motor temperature measurement and thermal protection settings.

197

32 Automatic reset

Configuration of conditions for automatic fault resets.

202

33 Supervision

Configuration of signal supervision.

202

34 User load curve

Configuration of user load curve.

205

35 Process variable

Selection and modification of process variables for display as
parameters 04.06 … 04.08.

207

36 Timed functions

Configuration of timers.

214

38 Flux ref

Flux reference and U/f curve settings.

218

40 Motor control

Motor control settings such as performance/noise optimization, slip gain,
voltage reserve and IR compensation.

219

Summary of Contents for ACQ810
























































































































































































































































































































































































Search results

Summary of Contents for ACQ810

Reviews:

Brands by name

Popular brands

ABB ACQ810, Firmware Manual

Search results

Summary of Contents for ACQ810

Reviews:

Brands by name

Popular brands