manualshive.com logo in svg

ABB ACQ810, Firmware Manual

Share
Download
ABB ACQ810 Firmware Manual Download Page 136

136   Parameters

In1St In2Dir

The source selected by 

10.02

 

Ext1 start in1

 is the start signal 

(0 = stop, 1 = start), the source selected by 

10.03

 

Ext1 start 

in2

 is the direction signal (0 = forward, 1 = reverse).

6

10.02

Ext1 start in1

Selects source 1 of start and stop commands for external 
control location EXT1. See parameter 

10.01

 

Ext1 start func

, 

selections 

In1

 and 

3-wire.

Note:

 This parameter cannot be changed while the drive is 

running.

DI1

Digital input DI1 (as indicated by 

02.01

 

DI status

, bit 0).

1073742337

DIO4

Digital input/output DIO4 (as indicated by 

02.03

 

DIO status

, 

bit 3).

1073938947

Timed func

Bit 4 of parameter 

06.14

 

Timed func stat

. The bit is on when 

at least one of the four timers configured in parameter group 

36 Timed functions

 is on.

1074005518

Const

Constant and bit pointer settings (see 

Terms and 

abbreviations

 on page 

109

).

-

Pointer

10.03

Ext1 start in2

Selects source 2 of start and stop commands for external 
control location EXT1. See parameter 

10.01

 

Ext1 start func

, 

selection 

3-wire.

Note:

 This parameter cannot be changed while the drive is 

running.

DI2

Digital input DI2 (as indicated by 

02.01

 

DI status

, bit 1).

1073807873

DI5

Digital input DI5 (as indicated by 

02.01

 

DI status

, bit 4).

1074004481

DIO5

Digital input/output DIO5 (as indicated by 

02.03

 

DIO status

, 

bit 4).

1074004483

Const

Bit pointer setting (see 

Terms and abbreviations

 on page 

109

).

-

Pointer

10.04

Ext2 start func

Selects the source of start and stop commands for external 
control location 2 (EXT2).

Note:

 This parameter cannot be changed while the drive is 

running.

Not sel

No start or stop command sources selected.

0

In1

The source of the start and stop commands is selected by 
parameter 

10.05

 

Ext2 start in1

. The state transitions of the 

source bit are interpreted as follows:

1

3-wire

The sources of the start and stop commands is selected by 
parameters 

10.05

 

Ext2 start in1

 and 

10.06

 

Ext2 start in2

. 

The state transitions of the source bits are interpreted as 
follows:

2

No.

Name/Value

Description

FbEq

State of source 

(via par

10.05

)

Command

0 -> 1

Start

1 -> 0

Stop

State of source 1 

(via par. 

10.05

)

State of source 2 

(via par. 

10.06

)

Command

0 -> 1

1

Start

Any

1 -> 0

Stop

Any

0

Stop

Summary of Contents for ACQ810

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands