manualshive.com logo in svg

ABB ACQ810, Firmware Manual

Share
Download
ABB ACQ810 Firmware Manual Download Page 285

Parameters   285

99.13

IDrun mode

Selects the type of the motor identification performed at the 
next start of the drive (for Direct Torque Control). During the 
identification, the drive will identify the characteristics of the 
motor for optimum motor control. After the ID run, the drive is 
stopped. 

Note:

 This parameter cannot be changed while the 

drive is running.
Once the ID run is activated, it can be cancelled by stopping 
the drive: If ID run has already been performed once, 
parameter is automatically set to NO. If no ID run has been 
performed yet, parameter is automatically set to 

Standstill

. In 

this case, the ID run must be performed.

Notes:

•  ID run can only be performed in local control (i.e. when 

drive is controlled via PC tool or control panel).

•  ID run cannot be performed if parameter 

99.05

 

Motor ctrl 

mode

 is set to 

Scalar

.

•  ID run must be performed every time any of the motor 

parameters (

99.06

…

99.12

) have been changed. 

Parameter is automatically set to 

Standstill

 after the motor 

parameters have been set.

•  Ensure that possible Safe torque off and emergency stop 

circuits are closed during ID run.

•  Mechanical brake is not opened by the logic for the ID 

run.

No

No motor ID run is requested. This mode can be selected 
only if the ID run (Normal/Reduced/Standstill) has already 
been performed once.

0

Normal

Normal ID run. Guarantees the best possible control 
accuracy. The ID run takes about 90 seconds. This mode 
should be selected whenever it is possible.

Notes:

•  The driven machinery must be de-coupled from the motor 

with Normal ID run, if the load torque is higher than 20%, 
or if the machinery is not able to withstand the nominal 
torque transient during the ID run.

•  Check the direction of rotation of the motor before starting 

the ID run. During the run, the motor will rotate in the 
forward direction.

WARNING! 

The motor will run at up to approximately 

50…100% of the nominal speed during the ID run. 
ENSURE THAT IT IS SAFE TO RUN THE MOTOR 

BEFORE PERFORMING THE ID RUN!

1

No.

Name/Value

Description

FbEq

Summary of Contents for ACQ810

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands