manualshive.com logo in svg

ABB ACQ810, Firmware Manual

Share
Download
ABB ACQ810 Firmware Manual Download Page 74

74   Program features

Application control

„

Application macros

See chapter 

Application macros

 (page 

87

).

„

Timers

It is possible to define four different daily or weekly time periods. The time periods can 
be used to control four different timers. The on/off statuses of the four timers are 
indicated by bits 0…3 of parameter 

06.14

 

Timed func stat

, from where the signal can 

be connected to any parameter with a bit pointer setting (see page 

109

). In addition, 

bit 4 of parameter 

06.14

 is on if any one of the four timers is on.

Each time period can be assigned to multiple timers; likewise, a timer can be 
controlled by multiple time periods.

The figure below presents how different time periods are active in daily and weekly 
modes.

Monday

T

ue

sday

Wedne

sday

T

hur

sday

F

riday

Satur

day

S

unday

Monday

T

ue

sday

Wedne

sday

Time period 1:

 Start time 00:00:00; Stop time 00:00:00 or 24:00:00; Start on Tuesday; Stop 

day Sunday

Time period 2:

 Start time 03:00:00; Stop time 23:00:00; Start day Wednesday; Stop day 

Wednesday

Time period 3:

 Start time 21:00:00; Stop time 03:00:00; Start day Tuesday; Stop day Saturday

Time period 4:

 Start time 12:00:00; Stop time 00:00:00 or 24:00:00; Start day Thursday; Stop 

day Tuesday

T

hur

sday

Time period 1

(weekly)

Time period 4

(daily)

Time period 4

(weekly)

Time period 1

(daily)

Time period 2

(weekly)

Time period 2

(daily)

Time period 3

(weekly)

Time period 3

(daily)

Summary of Contents for ACQ810

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands