manualshive.com logo in svg

ABB ACQ810, Firmware Manual

Share
Download
ABB ACQ810 Firmware Manual Download Page 283

Parameters   283

0.00 …100000.00 
mH

Leakage inductance.

100 = 1 mH

99

99 Start-up data

Language selection, motor configuration and ID run settings.

99.01

Language

Selects the language of the control panel displays.

Note:

 Not all languages listed below are necessarily 

supported.

English

English.

0809

Deutsch

German.

0407

Italiano

Italian.

0410

Espanol

Spanish.

040A

Nederlands

Dutch.

0413

Francais

French.

040C

Dansk

Danish.

0406

Russki

Russian.

0419

Polski

Polish.

0415

Turkce

Turkish.

041F

Magyar

Hungarian.

040E

99.05

Motor ctrl mode

Selects the motor control mode.

DTC

Direct torque control. This mode is suitable for most 
applications.

Note:

 Instead of direct torque control, use scalar control

• with multimotor applications 1) if the load is not equally 

shared between the motors, 2) if the motors are of 
different sizes, or 3) if the motors are going to be changed 
after the motor identification (ID run),

• if the nominal current of the motor is less than 1/6 of the 

nominal output current of the drive,

• if the drive is used with no motor connected (for example, 

for test purposes),

• if the drive runs a medium-voltage motor through a step-

up transformer.

0

Scalar

Scalar control. This mode is suitable in special cases where 
DTC cannot be applied. In scalar control, the drive is 
controlled with a frequency reference. The outstanding 
motor control accuracy of DTC cannot be achieved in scalar 
control. Some standard features are disabled in scalar 
control mode.

Note:

 Correct motor run requires that the magnetizing 

current of the motor does not exceed 90% of the nominal 
current of the inverter.
See also section 

Scalar motor control

 on page 

70

.

1

99.06

Mot nom current

Defines the nominal motor current. Must be equal to the 
value on the motor rating plate. If multiple motors are 
connected to the drive, enter the total current of the motors.

Notes:

•  Correct motor run requires that the magnetizing current of 

the motor does not exceed 90% of the nominal current of 
the drive.

•  This parameter cannot be changed while the drive is 

running.

No.

Name/Value

Description

FbEq

Summary of Contents for ACQ810

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands