ABB ACQ810 Firmware Manual Download Page 281

Page: 281 / 376

Parameters 281

Average

The current energy monitoring period (parameter

05.20

kWh

current read

) is compared to the average of the two previous

periods (

and

83.02

Mon period

Defines the length of an energy monitoring period. The first
period starts when the drive is powered up.

0.00 … 35791394.11
h

Length of monitoring period.

1 = 1 min

83.03

kWh limit

Consumed energy limit for parameter

, selection

0…2147483647
kWh

Energy limit.

1 = 1 kWh

83.04

Mon tolerance

Tolerance for energy limit. The energy consumption may
exceed the reference energy by this tolerance value until the
action defined by parameter

83.05

Energy mon ctrl

is taken.

0…2147483647
kWh

Tolerance.

1 = 1 kWh

83.05

Energy mon ctrl

Defines the action that is taken if the energy consumption
exceeds the tolerance limits.

Not sel

No action taken.

Alarm

The drive generates alarm

ENERGY LIMIT

83.06

Energy reset

Resets the energy monitoring counters.

No reset. The parameter automatically reverts to this value
after a reset.

Period

Resets the periodic energy counters (parameters

05.20

…

05.22

Month

Resets the monthly energy counters (parameters

05.23

…

05.35

94 Ext IO conf

I/O extension configuration.

94.01

Ext IO1 sel

Activates an I/O extension installed into Slot 1. Depending
on the module used, enables
• digital input DI7
• digital input/outputs DIO3…DIO6
• analog inputs AI3…AI5
• analog output AO3 or
• relay outputs RO3…RO6.

None

No extension installed into Slot 1.

FIO-01

FIO-01 extension installed into Slot 1. Additional 4 × DIO
and 2 × RO are in use.

FIO-11

FIO-11 extension installed into Slot 1. Additional 2 × DIO,
3 × AI and 1 × AO are in use.

FIO-21

FIO-21 extension installed into Slot 1. Additional 1 × DI,
1 × AI and 2 × RO are in use.

FIO-31

FIO-31 extension installed into Slot 1. Additional 4 × RO are
in use.

95 Hw configuration

Diverse hardware-related settings.

95.01

Ctrl boardSupply

Selects how the drive control unit is powered.

No.

Name/Value

Description

FbEq

Summary of Contents for ACQ810
























































































































































































































































































































































































Search results

Summary of Contents for ACQ810

Reviews:

Brands by name

Popular brands

ABB ACQ810, Firmware Manual

Search results

Summary of Contents for ACQ810

Reviews:

Brands by name

Popular brands