manualshive.com logo in svg

ABB ACQ810, Firmware Manual

Share
Download
ABB ACQ810 Firmware Manual Download Page 221

Parameters   221

Moderate

Flux level is limited during the braking. Deceleration time is 
longer compared to full braking.

1

Full

Maximum braking power. Almost all available current is used 
to convert the mechanical braking energy to thermal energy 
in the motor.

2

44

44 Maintenance

Maintenance counter configuration.
See also section 

Maintenance counters

 on page 

82

.

44.01

Ontime1 func

Configures on-time counter 1. This counter runs whenever 
the signal selected by parameter 

44.02

 

Ontime1 src

 is on. 

After the limit set by parameter 

44.03

 

Ontime1 limit

 is 

reached, an alarm specified by parameter 

44.04

 

Ontime1 

alm sel

 is given, and the counter reset.

The current value of the counter is readable from parameter 

04.09

 

Counter ontime1

. Bit 0 of 

06.15

 

Counter status

 

indicates that the count has exceeded the limit.

44.02

Ontime1 src

Selects the signal to be monitored by on-time counter 1. See 
parameter 

44.01

 

Ontime1 func

.

RO1

Relay output RO1 (as indicated by 

02.02

 

RO status

, bit 0).

1073742338

Running

Bit 3 of 

06.01

 

Status word1

 (see page 

126

).

1073939969

Charged

Bit 9 of 

06.02

 

Status word2

 (see page 

127

).

1074333186

Const

Bit pointer setting (see 

Terms and abbreviations

 on page 

109

).

-

Pointer

44.03

Ontime1 limit

Sets the alarm limit for on-time counter 1. See parameter 

44.01

 

Ontime1 func

.

0…2147483647 s

Alarm limit for on-time counter 1.

44.04

Ontime1 alm sel

Selects the alarm for on-time counter 1. See parameter 

44.01

 

Ontime1 func

.

On-time1

Pre-selectable alarm for on-time counter 1.

0

Device clean

Pre-selectable alarm for on-time counter 1.

1

Add cool fan

Pre-selectable alarm for on-time counter 1.

2

Cabinet fan

Pre-selectable alarm for on-time counter 1.

3

Dc-capacitor

Pre-selectable alarm for on-time counter 1.

4

Mot bearing

Pre-selectable alarm for on-time counter 1.

5

No.

Name/Value

Description

FbEq

Bit

Function

0

Counter mode
0 = Loop: If alarm is enabled by bit 1, the alarm stays active only for 10 seconds.
1 = Saturate: If alarm is enabled by bit 1, the alarm stays active until reset.

1

Alarm ena (Alarm enable)
0 = Disable: No alarm is given when limit is reached.
1 = Enable: Alarm is given when limit is reached.

Summary of Contents for ACQ810

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands