manualshive.com logo in svg

ABB ACQ810, Firmware Manual

Share
Download
ABB ACQ810 Firmware Manual Download Page 54

54   Control locations

Local control vs. external control

The drive has two main control locations: external and local. The control location is 
selected with the LOC/REM key on the control panel or with the PC tool (Take/
Release button).

„

Local control

The control commands are given from the control panel keypad or from a PC 
equipped with DriveStudio when the drive is in local control. A speed control mode is 
available for local control.

Local control is mainly used during commissioning and maintenance. The control 
panel always overrides the external control signal sources when used in local control. 
Changing the control location to local can be disabled by parameter 

16.01

 

Local lock

.

The user can select by a parameter (

30.03

 

Local ctrl loss

) how the drive reacts to a 

control panel or PC tool communication break.

Control panel or PC tool 

(DriveStudio/SPC)

(optional)

Fieldbus adapter 
Fxxx in Slot 2

*Extra inputs/outputs can be added by installing an optional I/O extension module (FIO-xx) 
into drive Slot 1.

MOTOR

PLC 

(= Programmable 

Logic Controller)

M

3~

ACQ810

Drive-to-drive link or 
embedded fieldbus 
interface

*I/O

Local control

External control

Summary of Contents for ACQ810

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands