manualshive.com logo in svg

ABB ACQ810, Firmware Manual

Share
Download
ABB ACQ810 Firmware Manual Download Page 105

Application macros   105

Multipump control macro

„

Description and typical application

This macro is suitable for pump stations that consist of multiple pumps, each 
controlled by a separate drive.

The configuration supports redundancy so that in case of a pump failure or 
maintenance action on one drive, the remaining drives continue operation. The drives 
communicate with each other through the drive-to-drive (D2D) link. It is possible to 
distribute two analog and five digital signals from a specific drive to the other drives 
via the drive-to-drive link (see parameters 

76.11

…

76.16

).

The multipump macro has three modes selectable by parameter.

• In master-regulated operation, when the load increases, the master’s speed 

increases. After the master has reached full speed, other drives are started one 
by one. Depending on a parameter setting, the master status is retained by the 
first drive, or passed on to the drive that was started last.

• Follower drives are run either at a pre-set speed (i.e. at the optimal operating 

point of the pump) or at the same speed as the master. In both these modes, 
drives can be prioritized so that the one with the highest priority is the first to be 
started.

• In direct follower operation, all drives run in synchronization with the master. This 

mode can be used in time-critical applications or for testing of the pump 
installation.

„

Default settings

Below is a listing of default parameter values that differ from those listed in chapter 

Additional parameter data

 (page 

287

).

Parameter

Multipump control 
macro default

No.

Name

16.16

Menu set active

M pump short

16.20

Macro selected

Multi pump

XD2D

XD2D

XD2D

DI

AI

XD2D

Drive 1

Drive 2

Drive 3

Drive 8

Control data + shared signals

Summary of Contents for ACQ810

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands