ABB ACQ810 Firmware Manual Download Page 70 | Manualshive

Page: 70 / 376

ABB ACQ810 Firmware Manual Download Page 70

70 Program features

Settings

Parameter group

23 Speed ctrl

(page

).

Diagnostics

Parameters

Motor speed rpm

(page

),

Motor speed %

(page

) and

Motor speed est

(page

).

Scalar motor control

It is possible to select scalar control as the motor control method instead of Direct
Torque Control (DTC). In scalar control mode, the drive is controlled with a frequency
reference. However, the outstanding performance of DTC is not achieved in scalar
control.

It is recommended to activate the scalar motor control mode in the following
situations:

• In multimotor drives: 1) if the load is not equally shared between the motors, 2) if

the motors are of different sizes, or 3) if the motors are going to be changed after
motor identification (ID run)

• If the nominal current of the motor is less than 1/6 of the nominal output current of

the drive

• If the drive is used without a motor connected (for example, for test purposes).

In scalar control, some standard features are not available.

Settings

Parameter

Motor ctrl mode

(page

).

IR compensation for a scalar controlled drive

IR compensation is active only when
the motor control mode is scalar. When
IR compensation is activated, the drive
gives an extra voltage boost to the
motor at low speeds. IR compensation
is useful in applications that require a
high break-away torque.

In Direct Torque Control (DTC), no IR
compensation is possible or needed.

Settings

Parameter

IR-compensation

(page

).

f

(Hz)

Motor voltage

No compensation

IR Compensation

«
...
68
69
70
71
72
...
»

Summary of Contents for ACQ810

























































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands