ABB ACQ810 Firmware Manual Download Page 112

Page: 112 / 376

112 Parameters

Parameter listing

No.

Name/Value

Description

FbEq

01 Actual values

Basic signals for monitoring of the drive.

01.01

Motor speed rpm

Filtered, estimated motor speed in rpm. The filter time
constant can be adjusted using parameter

19.03

MotorSpeed filt

100 = 1 rpm

01.02

Motor speed %

Actual speed in percent of the motor synchronous speed.

100 = 1%

01.03 Output frequency

Estimated drive output frequency in Hz.

100 = 1 Hz

01.04

Motor current

Measured motor current in A.

100 = 1 A

01.05

Motor current %

Motor current in percent of the nominal motor current.

10 = 1%

01.06

Motor torque

Motor torque in percent of the nominal motor torque. See
also parameter

01.29

Torq nom scale

10 = 1%

01.07

Dc-voltage

Measured intermediate circuit voltage.

100 = 1 V

01.14

Motor speed est

Estimated motor speed in rpm.

100 = 1 rpm

01.15

Temp inverter

Estimated IGBT temperature in percent of fault limit.

10 = 1%

01.17

Motor temp1

Measured temperature of motor 1 in degrees Celsius when a
KTY sensor is used. (With a PTC sensor, the value is always
0.)

10 = 1 °C

01.18

Motor temp2

Measured temperature of motor 2 in degrees Celsius when a
KTY sensor is used. (With a PTC sensor, the value is always
0.)

10 = 1 °C

01.19

Used supply volt

Either the user-given supply voltage (parameter

47.04

Supply voltage

), or, if auto-identification is enabled by

parameter

47.03

SupplyVoltAutoId

, the automatically

determined supply voltage.

10 = 1 V

01.21

Cpu usage

Microprocessor load in percent.

1 = 1%

01.22

Power inu out

Drive output power in kW or hp, depending on setting of
parameter

16.17

Power unit

100 = 1 kW
or hp

01.23

Motor power

Measured motor shaft power in kW or hp, depending on
setting of parameter

16.17

Power unit

100 = 1 kW
or hp

01.24

kWh inverter

Amount of energy that has passed through the drive (in
either direction) in kilowatt-hours. Can be reset by entering a
0 using the DriveStudio PC tool.

1 = 1 kWh

01.25

kWh supply

Amount of energy that the drive has taken from the AC
supply in kilowatt-hours. Can be reset by entering a 0 using
the DriveStudio PC tool.

1 = 1 kWh

01.26

On-time counter

On-time counter. The counter runs when the drive is
powered. Can be reset by entering a 0 using the DriveStudio
PC tool.

1 = 1 h

01.27

Run-time counter

Motor run-time counter. The counter runs when the inverter
modulates. Can be reset by entering a 0 using the
DriveStudio PC tool.

Note:

The drive logic uses this value for equalization of

pump running duties. See section

Autochange

(page

1 = 1 h

01.28

Fan on-time

Running time of the drive cooling fan. Can be reset by
entering a 0 using the DriveStudio PC tool.

1 = 1 h

01.29

Torq nom scale

Nominal torque which corresponds to 100%.

Note:

This value is copied from parameter

99.12

Mot nom

torque

if entered. Otherwise the value is calculated.

1000 =
1 N•m

Summary of Contents for ACQ810
























































































































































































































































































































































































Search results

Summary of Contents for ACQ810

Reviews:

Brands by name

Popular brands

ABB ACQ810, Firmware Manual

Search results

Summary of Contents for ACQ810

Reviews:

Brands by name

Popular brands