manualshive.com logo in svg

ABB ACQ810, Firmware Manual

Share
Download
ABB ACQ810 Firmware Manual Download Page 337

Control through the embedded fieldbus interface   337

„

Control word and Status word

The Fieldbus control word (CW) is a 16-bit or 32-bit packed boolean word. It is the 
principal means of controlling the drive from a fieldbus system. The Control word is 
sent by the fieldbus controller to the drive. The drive switches between its states 
according to the bit-coded instructions of the Control word. In the embedded fieldbus 
communication, the CW is written to drive parameter 

02.36 EFB main cw

 from where 

it can be used in the control of the drive. The Fieldbus CW is either written to the drive 
Control word as it is, or the data is converted. See section 

About the EFB 

communication profiles

 on page 

338

.

The Fieldbus status word (SW) is a 16-bit or 32- bit packed boolean word. It contains 
status information from the drive to the fieldbus controller. In the embedded fieldbus 
communication, the SW is read from drive parameter 

02.37

 

EFB main sw

. The Drive 

status word is either written to the fieldbus SW as it is or the data is converted. See 
section 

About the EFB communication profiles

 on page 

338

.

„

References

Fieldbus references (REF1 and REF2) are 16-bit or 32-bit signed integers. The 
contents of each reference word can be used as the speed, frequency, or process 
reference. In the embedded fieldbus communication, the REF1 and REF2 are written 
to 

02.38

 

EFB main ref1

 and 

02.39 EFB main ref2

 from where you can use them in the 

control of the drive. The references are either written to the drive references as they 
are, or the values are scaled. See section 

About the EFB communication profiles

 on 

page 

338

.

„

Actual values

Fieldbus actual signals (ACT1 and ACT2) are 16-bit or 32-bit signed integers. They 
convey selected drive parameter values from the drive to the master. The drive 
values are either written to the fieldbus actual values as they are, or the values are 
scaled. See section 

About the EFB communication profiles

 on page 

338

.

„

Data inputs/outputs

Data input/output (I/O) are 16-bit or 32-bit words containing selected drive parameter 
values. Parameters 

58.35

 

Data I/O 1

 … 

58.58 Data I/O 24

 define the addresses from 

which the master either reads data (input) or to which it writes data (output).

Summary of Contents for ACQ810

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands