manualshive.com logo in svg

ABB ACQ810, Firmware Manual

Share
Download
ABB ACQ810 Firmware Manual Download Page 338

338   Control through the embedded fieldbus interface

About the EFB communication profiles

A communication profile defines the rules for data transfer in between the drive and 
the fieldbus master, for example: 

• if packed boolean words are converted and how 
• if the signal values are scaled and how
• how the drive register addresses are mapped for the fieldbus master.

You can configure the drive to receive and send messages according to one of the 
four profiles: the ABB Drives classic profile, ABB Drives enhanced profile, 16-bit DCU 
profile or 32-bit DCU profile. For either one of the ABB Drives profile, the embedded 
fieldbus interface of the drive converts the fieldbus data to and from the native data 
used in the drive. Both DCU profiles are transparent, that is, no data conversion is 
done. The figure below illustrates the effect of the profile selection.

Profile selection

Communication profile selection with parameter 

58.06

 

Control profile

 are:

• (0) 

ABB Classic

• (1) 

ABB Enhanced

• (2) 

DCU 16-bit

• (2) 

DCU 32-bit

58.06

SEL

Data 

conv. & 

scaling

0

1

2

3

Fieldbus

Drive

Summary of Contents for ACQ810

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands