ABB ACQ810 Firmware Manual Download Page 319

Page: 319 / 376

Fault tracing 319

2077

EFB COMM LOSS
(0x7540)

Embedded fieldbus
interface has been taken
into use, and there is a
communication break
between the drive and the
master station.

Check:
• selection of the parameter which

enables/disables EFB communication

(

58.01

Protocol ena sel

)

• EFB connection at terminal XD2D on

the JCON board

• status of the fieldbus master (online/

offline)

• settings of the communication

supervision function (parameter

58.09

Comm loss action

2201

PIPEFILL TIMEOUT

Maximum allowed time for
the Pipefill function
exceeded.

Check the pump system.
Check parameters

81.28

….

81.35

2202

MIN FLOW

Measured flow below
minimum limit.

Check the pump system for reasons
such as leaks that might cause a loss of
measured flow.
Check parameters

81.18

….

81.24

2203

MAX FLOW

Measured flow above
maximum limit.

Check the pump system for reasons that
might cause an increase in measured
flow.
Check parameters

81.18

….

81.24

2204

LOW PRESSURE

Pressure at pump inlet too
low.

Check for a closed valve on the inlet side
of the pump.
Check piping for leaks.

2205

HIGH PRESSURE

Pressure at pump outlet too
high.

Check piping for blocks.

2206

VERY LOW PRESS

Pressure at pump inlet too
low.

Check for a closed valve on the inlet side
of the pump.
Check piping for leaks.

2207

VERY HIGH PRESS

Pressure at pump outlet too
high.

Check piping for blocks.

2208

PROFILE HIGH

Application profile protection
limit exceeded (see
parameters

81.25

…

81.27

Check the piping for leaks.
Check the general condition of the
components of the pumping station.

2209

MAX CLEANINGS

Maximum number of
cleaning sequences
exceeded (see parameter
group

82 Pump cleaning

Check for reasons that might have had
an increasing effect on the monitored
signal (parameter

82.09

). For example,

increased viscosity of the fluid, or faulty
pump bearings may increase the current
drawn by the motor, and trigger the
cleaning sequence more frequently.

2210

ALL PUMPS INLOCKD

b10

All interlock signals are off,
indicating no pumps are
available.

Check the interlock settings in parameter
group

78 Pump autochange

Check that the pumps are switched on.
Check the interlock wiring from the
pumps.

2211

ENERGY LIMIT

b10

b11

Energy consumption limit
exceeded (see parameter
group

83 Energy

monitoring

Check for reasons for increased energy
consumption.

Code

Alarm (fieldbus code),
other information

Cause

What to do

Summary of Contents for ACQ810
























































































































































































































































































































































































Search results

Summary of Contents for ACQ810

Reviews:

Brands by name

Popular brands

ABB ACQ810, Firmware Manual

Search results

Summary of Contents for ACQ810

Reviews:

Brands by name

Popular brands