VeEX VePAL TX300M Скачать руководство пользователя страница 335

Страница: 335 / 421

15.5 Throughput Testing (Multiple Streams)

Overview:

The throughput application (or the multiple streams application) performs the following measurements: throughput performance,

frame loss analysis, delay analysis, frame/packet arrival analysis, received traffic type analysis, and received traffic frame size

analysis. On the transmit side, the throughput application allows for the configuration of up to 8 traffic streams with their own

MAC and IP addresses, VLAN tags (up to 3 per stream), bandwidth/rate, frame size, and L2 and/or L3 quality of service (QoS)

parameters. On the receiver end the traffic is analyzed on a per stream (up to 8 streams) basis as well as a global or aggregate

measurement.

This application is very useful in verifying the transport of traffic with different prioritization settings across a network link. The test

helps verify that the network can handle high priority traffic and low priority traffic accordingly.

Setup

General Settings
MX Discover and Control Settings
Per Stream Configurations
Traffic Settings
Error Injection Settings
Alarm Injection Settings
Summary

Starting/ Stopping a Throughput Test
Results

Global Aggregate Results
Per Stream Results
Saving Results

Go back to top

Go back to TOC

15.5.1 Setup

Unless otherwise noted, the Frame Header and related setups are the same as the ones described in section

15.2 BERT

and

15.3 RFC 2544

. The following parameters must be configured prior to performing a Throughput test:

Number of streams (See

General Settings

below)

Bandwidth per stream (See

General Settings

below)

Test layer

Frame Type

VLAN tag(s)

MPLS tag(s)

Frame header per stream (if applicable)

Traffic profile per stream (if applicable)

Error injection per stream (if applicable)

Control settings of the far-end device(s) (if applicable)

Go back to top

Go back to TOC

15.5.1.1 General Throughput Settings (Global Configuration)

Page 1:

# of Streams:

From 1 to 10 streams.

Stream #:

Allocated Bandwidth per Stream: The total bandwidth for all streams cannot exceed 100%.

Total (%):

Sum of all stream rates in %.

Throughput Setup - General Settings

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды